1930953 LINK AS Caterpillar parts
938G, 938G II, 938H
Rating:
Alternative (cross code) number:
CA1930953
193-0953
1930953
CA1930953
193-0953
1930953
Weight: 80 pounds 36 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
NUEPWRFA 1908556 1907640 1909142 42522674 1930953 2133558 9941058 1900953 FUEL FILTER Compatible for IVECO 29-11 Turbo 29-13 Turbo 29-9 35-11 Turbo 35-13 Turbo 35-9 40-11 Turbo 65-15 Turbo
NUEPWRFA Part number: 1908556 1907640 1909142 42522674 1930953 2133558 9941058 1900953 || Compatible for IVECO 29-11 Turbo 29-13 Turbo 29-9 35-11 Turbo 35-13 Turbo 35-9 40-11 Turbo 45-11 Turbo 45-13 Turbo 49-11 Turbo 49-13 Turbo 50-11 Turbo 50-13 Turbo 59-13 Turbo 60-15 Turbo 65-15 Turbo || Approx. Dimensions: Outer Diameter 76 mm (2.99 inch) Thread Size M16 x 1.5 Length 148 mm (5.83 inch) Gasket OD 72 mm (2.83 inch) Gasket ID 62.2 mm (2.45 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
NUEPWRFA Part number: 1908556 1907640 1909142 42522674 1930953 2133558 9941058 1900953 || Compatible for IVECO 29-11 Turbo 29-13 Turbo 29-9 35-11 Turbo 35-13 Turbo 35-9 40-11 Turbo 45-11 Turbo 45-13 Turbo 49-11 Turbo 49-13 Turbo 50-11 Turbo 50-13 Turbo 59-13 Turbo 60-15 Turbo 65-15 Turbo || Approx. Dimensions: Outer Diameter 76 mm (2.99 inch) Thread Size M16 x 1.5 Length 148 mm (5.83 inch) Gasket OD 72 mm (2.83 inch) Gasket ID 62.2 mm (2.45 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
NUEPWRFA 1930953 4795601 1909142 4753103 94795601 01930953 0001930010 FUEL FILTER Compatible for FIAT 1180DT 1280 1280DT 1380 160.9 180-90 880-5DT 955C 980DT FIAT 8065 8325.25 8055.04 TRACTOR
NUEPWRFA Part number: 1930953 4795601 1909142 4753103 94795601 01930953 0001930010 || Compatible for FIAT 1180DT 1280 1280DT 1380 160.9 180-90 880-5DT 955C 980DT FIAT 8065 8325.25 8055.04 TRACTOR || Approx. Dimensions: Outer Diameter 76 mm (2.99 inch) Thread Size M16 x 1.5 Length 148 mm (5.83 inch) Gasket OD 72 mm (2.83 inch) Gasket ID 62.2 mm (2.45 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
NUEPWRFA Part number: 1930953 4795601 1909142 4753103 94795601 01930953 0001930010 || Compatible for FIAT 1180DT 1280 1280DT 1380 160.9 180-90 880-5DT 955C 980DT FIAT 8065 8325.25 8055.04 TRACTOR || Approx. Dimensions: Outer Diameter 76 mm (2.99 inch) Thread Size M16 x 1.5 Length 148 mm (5.83 inch) Gasket OD 72 mm (2.83 inch) Gasket ID 62.2 mm (2.45 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
01930953 Fuel Filter 1930953 Oil-water separator Spin-On Compatible with FIAT 1180DT, 1280, 1280DT, 1380, 160.9, 180-90, 880-5DT, 955C, 980DT - 2 pcs
STRDYUE Replaces OE : 1930953 || Compatible with FIAT 1180DT, 1280, 1280DT, 1380, 160.9, 180-90, 880-5DT, 955C, 980DT ;;Compatible with FODEN S104, S104R, S106, S106T ,S108, S108T ; || easy to use:easy to install,Standardized manufacturing and quality material to ensure excellent performance and excellent service life. || All OEM part numbers and logos are for identification purposes only, if you are unsure if this accessory is compatible with your device, please send us your device model number so we can assist you.
STRDYUE Replaces OE : 1930953 || Compatible with FIAT 1180DT, 1280, 1280DT, 1380, 160.9, 180-90, 880-5DT, 955C, 980DT ;;Compatible with FODEN S104, S104R, S106, S106T ,S108, S108T ; || easy to use:easy to install,Standardized manufacturing and quality material to ensure excellent performance and excellent service life. || All OEM part numbers and logos are for identification purposes only, if you are unsure if this accessory is compatible with your device, please send us your device model number so we can assist you.
Number on catalog scheme:
13
For full view, you need register
Information:
Remove Pistons
start by: a) remove cylinder headb) remove oil pump1. Remove the carbon ridge from the top inside surface of the cylinder liners.2. Turn the crankshaft until two pistons are at bottom center. 3. Remove the connecting rod caps (1) from these pistons and push the pistons up until the rings are free of the cylinder liner. 4. Remove the two pistons.5. Do Steps 2, 3, and 4 for the remainder of the pistons.Install Pistons
1. Put clean SAE 30 engine oil on the crankshaft bearing journals and cylinder liners.2. Put clean SAE 30 engine oil on the pistons and connecting rod bearings. 3. Install the pistons with tool (A) making sure the "V" mark on the piston is in alignment with the "V" mark on the cylinder block. Push the lower end of the rod over the crankshaft journal to prevent causing damage to the crankshaft.4. Put clean SAE 30 engine oil on threads of the bolts that hold the caps. 5. Put caps in position on the connecting rods and install nuts. Tighten both nuts to a torque of 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the nuts and at the end of both bolts and then tighten both nuts 90° from the mark.
During installation of the connecting rod cap, be sure that the number on the cap is in alignment with and is the same as the number on side of the connecting rod.
6. Turn the crankshaft until the next two bearing journals are at bottom center.7. Do Steps 2 through 5 for the remainder of the pistons.end by: a) install oil pumpb) install cylinder headDisassemble Pistons
start by: a) remove pistons 1. Remove rings from piston with tool (A). 2. Remove snap ring (3), piston pin (1) and connecting rod (2) from piston.Assemble Pistons
If a replacement of the rod pin bearing is made, use a pin boring machine to make the bearing the correct size. See SPECIAL INSTRUCTION FORM GMG02394. 1. Install rod on piston with bearing tab groove (2) and number identification on the same side as the "V" mark (1) on top of the piston.2. Install piston pin and snap rings. 3. When the old pistons are used, clean the piston grooves with tool (A) before installing new rings.4. Install rings on piston with tool (B). The ring openings must be 90° apart.end by: a) install pistons
start by: a) remove cylinder headb) remove oil pump1. Remove the carbon ridge from the top inside surface of the cylinder liners.2. Turn the crankshaft until two pistons are at bottom center. 3. Remove the connecting rod caps (1) from these pistons and push the pistons up until the rings are free of the cylinder liner. 4. Remove the two pistons.5. Do Steps 2, 3, and 4 for the remainder of the pistons.Install Pistons
1. Put clean SAE 30 engine oil on the crankshaft bearing journals and cylinder liners.2. Put clean SAE 30 engine oil on the pistons and connecting rod bearings. 3. Install the pistons with tool (A) making sure the "V" mark on the piston is in alignment with the "V" mark on the cylinder block. Push the lower end of the rod over the crankshaft journal to prevent causing damage to the crankshaft.4. Put clean SAE 30 engine oil on threads of the bolts that hold the caps. 5. Put caps in position on the connecting rods and install nuts. Tighten both nuts to a torque of 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the nuts and at the end of both bolts and then tighten both nuts 90° from the mark.
During installation of the connecting rod cap, be sure that the number on the cap is in alignment with and is the same as the number on side of the connecting rod.
6. Turn the crankshaft until the next two bearing journals are at bottom center.7. Do Steps 2 through 5 for the remainder of the pistons.end by: a) install oil pumpb) install cylinder headDisassemble Pistons
start by: a) remove pistons 1. Remove rings from piston with tool (A). 2. Remove snap ring (3), piston pin (1) and connecting rod (2) from piston.Assemble Pistons
If a replacement of the rod pin bearing is made, use a pin boring machine to make the bearing the correct size. See SPECIAL INSTRUCTION FORM GMG02394. 1. Install rod on piston with bearing tab groove (2) and number identification on the same side as the "V" mark (1) on top of the piston.2. Install piston pin and snap rings. 3. When the old pistons are used, clean the piston grooves with tool (A) before installing new rings.4. Install rings on piston with tool (B). The ring openings must be 90° apart.end by: a) install pistons
Caterpillar parts catalog:
Parts link Caterpillar catalog:
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
4Q1346
LINK & BEARING AS
938G, 938G II, 938H
938G, 938G II, 938H
924G, 924GZ, 924H, 924HZ, 928F, 928HZ, 930G, 936, 936F, 938F, 938G, 938G II, G936, IT28F, IT38F, IT38G, IT38G II
936, 936F, 938F, 938G, G936
1367966
LINK AS-BEARING
938F, 938G, 938H
938F, 938G, 938H
1443266
LINK AS
938G
938G
2308123
LINK AS
938G II, 938H
938G II, 938H
2661983
LINK
938H, IT38H
938H, IT38H
2636330
LINK
938H, IT38H
938H, IT38H
3196949
LINK AS
938H
938H
3109306
LINK AS
938H
938H
3471250
LINK AS
938H
938H
1482423
LINK AS-TILT
962G, IT62G, IT62G II, IT62H
962G, IT62G, IT62G II, IT62H
1482422
LINK AS-TILT
962G, IT62G, IT62G II, IT62H
962G, IT62G, IT62G II, IT62H
1482416
LINK AS-TILT
962G, IT62G, IT62G II, IT62H
962G, IT62G, IT62G II, IT62H
1271579
LINK
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT62G, IT62G II, IT62H
1311859
LINK-TAG
631E, 633E II, 637E
631E, 633E II, 637E
1311860
LINK-TAG
631E, 633E II, 637E
631E, 633E II, 637E
1781064
LINK AS-TILT
902, 906
902, 906
1382376
LINK AS-TILT
902, 906
902, 906
1787350
LINK AS-FRAME LOCK
902, 906, 908
902, 906, 908
1575967
LINK
902, 906
902, 906
902, 906, 908
1443266
LINK AS
938G
938G