1V4606 LINK-TRACK MASTER Caterpillar parts
312B L, 312C, 941, 943, 955K, D4D, D4E, D4E SR, D5C
Rating:
Alternative (cross code) number:
CA1V4606
1V-4606
1V4606
CA1V4606
1V-4606
1V4606
Weight: 3 pounds 1 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compatible equipment models: 1V4606:
Number on catalog scheme:
8
For full view, you need register
Information:
If the metal particle detector causes a shutdown, inspect the detector.
Illustration 1 g00745503
Metal particle detector (1) Cover
Use a 1/2 inch ratchet to remove cover (1) and the O-ring seal from the detector.
Remove the grid and the O-ring seal for the grid from the inside of the detector.
If metal particles are found, determine the source of the particles. Make repairs, as needed.
Metal particles in the lube oil may indicate a serious condition that requires immediate attention.If metal particles are found in the grid of the detector, do not start the engine until the source of the particles is found and the condition is corrected. Failure to do so could cause severe damage to the engine.
Clean the inside of the detector and clean the grid with nonflammable solvent.Note: To replace the O-ring seals and the grid, use the 165-5690 Particle Detector Kit .
Inspect the grid and the O-ring seals for good condition. Obtain new parts, if necessary.
Install the clean, dry grid and the O-ring seal for the grid.
Install the cover and the O-ring seal for the cover. Torque the cover to 54 N m (40 lb ft).
Illustration 1 g00745503
Metal particle detector (1) Cover
Use a 1/2 inch ratchet to remove cover (1) and the O-ring seal from the detector.
Remove the grid and the O-ring seal for the grid from the inside of the detector.
If metal particles are found, determine the source of the particles. Make repairs, as needed.
Metal particles in the lube oil may indicate a serious condition that requires immediate attention.If metal particles are found in the grid of the detector, do not start the engine until the source of the particles is found and the condition is corrected. Failure to do so could cause severe damage to the engine.
Clean the inside of the detector and clean the grid with nonflammable solvent.Note: To replace the O-ring seals and the grid, use the 165-5690 Particle Detector Kit .
Inspect the grid and the O-ring seals for good condition. Obtain new parts, if necessary.
Install the clean, dry grid and the O-ring seal for the grid.
Install the cover and the O-ring seal for the cover. Torque the cover to 54 N m (40 lb ft).
Caterpillar parts catalog:
Parts link Caterpillar catalog:
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 312B L, 312C, 312C L, 313B, 314C, 320C, 322B, 322B L, 322C, 322C FM, 323D L, 325C, 325D, 330B L, 330C, 330C L
311C, 312C, 312C L, 314C, 320C, 322C, 323D L, 325C, 325D, 330C, 330C L
311C, 312C, 312C L, 314C, 320C, 322B, 322C, 323D L, 325C, 325D, 330B L, 330C, 330C L
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
D4D, D4E
D4E, D8K
D4E, D7F, D8K
941, 943
312B L, 312C, 941, 943, D4D, D4E, D4E SR, D5C
312B L, 312C, 941, 943, D4D, D4E, D4E SR, D5C
215, 225, 312B L, 312C, 312D, 323D LN, 941, 943, D4D, D4E, D4E SR, D5C, PM-201, PM-565, PM-565B, PR-1000
215, 225, 312B L, 312C, 312D, 323D LN, 941, 943, D4D, D4E, D4E SR, D5C, PM-201, PM-565, PM-565B, PR-1000
307, 307B, 307C, 308C, 312C L
1152686
LINK & BEARING AS
307, 307B
307, 307B
1949830
LINK
312B L, 313B, 320C, 322B L, 322C, 322C FM, 325C, 330B L
312B L, 313B, 320C, 322B L, 322C, 322C FM, 325C, 330B L
1699755
LINK AS
312B L, 312C
312B L, 312C
1699754
LINK AS
312B L, 312C
312B L, 312C
1802686
LINK-TRACK
312B L, 312C, 312D
312B L, 312C, 312D
1802687
LINK-TRACK
312B L, 312C, 312D
312B L, 312C, 312D
312B L, 312C, 941, 943, D4D, D4E, D4E SR, D5C