2362423 LINK & BEARING AS Caterpillar parts
301.5, 301.6C
Rating:
Alternative (cross code) number:
CA2362423
236-2423
2362423
CA2362423
236-2423
2362423
Weight: 7 pounds 3 kg.
MINI HYD EXCAVATOR,
Number on catalog scheme:
8
For full view, you need register
Information:
Introduction
This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Safety
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
449-1802 Auxiliary Control Ar Revision -00
Part Number Description Media Number
377-8017 Chassis Wiring Gp GEHS0763
381-6033 Front Lines Gp GEHS0764
381-6034 Pump Lines Gp GEHS0765
381-6035 Pilot Lines Gp GEHS0766
444-9174 Film -
Illustration 2 g03667537
449-1802 Auxiliary Control Ar
Installation
The 449-1802 Auxiliary Control Ar is divided into several modules. Each module has a Special instruction associated to the module. Install the modules in the following order:
381-6034 Pump Lines Gp
381-6033 Front Lines Gp
381-6035 Pilot Lines Gp
377-8017 Chassis Wiring Gp
444-9174 FilmCalibration
Set the machine tool control system.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Process for setting Up the Work Tool"Calibrate the machine electronic control system.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Work Tool Parameter - Program"Set tool flows and pressures.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Work Tool - Select"Set the proper operating and/or relief pressures and the proper flows for the tool that is attached to the machine. Refer to the Operation and Maintenance Manual of the specific work tool installed.Principles of Operation
Reference: Excavator Tool Control System, KENR9616, "Systems Operation Section", "General Information"Serial Number Identification 444-9174 Film
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 3 g01742203
Illustration 4 g01743196
This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Safety
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
449-1802 Auxiliary Control Ar Revision -00
Part Number Description Media Number
377-8017 Chassis Wiring Gp GEHS0763
381-6033 Front Lines Gp GEHS0764
381-6034 Pump Lines Gp GEHS0765
381-6035 Pilot Lines Gp GEHS0766
444-9174 Film -
Illustration 2 g03667537
449-1802 Auxiliary Control Ar
Installation
The 449-1802 Auxiliary Control Ar is divided into several modules. Each module has a Special instruction associated to the module. Install the modules in the following order:
381-6034 Pump Lines Gp
381-6033 Front Lines Gp
381-6035 Pilot Lines Gp
377-8017 Chassis Wiring Gp
444-9174 FilmCalibration
Set the machine tool control system.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Process for setting Up the Work Tool"Calibrate the machine electronic control system.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Work Tool Parameter - Program"Set tool flows and pressures.
Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"Reference: Excavator Tool Control System, KENR9616, "Testing and Adjusting Section", "Work Tool - Select"Set the proper operating and/or relief pressures and the proper flows for the tool that is attached to the machine. Refer to the Operation and Maintenance Manual of the specific work tool installed.Principles of Operation
Reference: Excavator Tool Control System, KENR9616, "Systems Operation Section", "General Information"Serial Number Identification 444-9174 Film
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 3 g01742203
Illustration 4 g01743196
Caterpillar parts catalog:
Parts link Caterpillar catalog:
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
1394868
LINK AS
301.5
301.5
1394853
LINK AS
301.5
301.5
1394854
LINK AS
301.5
301.5
1394857
LINK AS
301.5
301.5
1394859
LINK AS
301.5
301.5
1572195
LINK
301.5, 302.5, 303.5, 304.5
301.5, 302.5, 303.5, 304.5
2498843
LINK
301.6C
301.6C
2526879
LINK & BEARING AS
301.6C
301.6C
2775155
LINK & BEARING AS
301.6C
301.6C
2775154
LINK-BUCKET
301.6C
301.6C
2920455
LINK AS
301.6C, 302.5C
301.6C, 302.5C
2299249
LINK AS
301.5, 301.6C
301.5, 301.6C
2299231
LINK
301.5, 301.6C
301.5, 301.6C
1493133
LINK AS
301.5
301.5
1493132
LINK
301.5
301.5
1493131
LINK AS
301.5
301.5
1396389
LINK AS
301.5
301.5
1394859
LINK AS
301.5
301.5
1394857
LINK AS
301.5
301.5
1394854
LINK AS
301.5
301.5
1394853
LINK AS
301.5
301.5
1394868
LINK AS
301.5
301.5
1488905
LINK
301.5, 302.5, 303.5, 304.5
301.5, 302.5, 303.5, 304.5