2430875 LINK & BEARING AS Caterpillar parts
305.5, 306
Rating:
Alternative (cross code) number:
CA2430875
243-0875
2430875
CA2430875
243-0875
2430875
Weight: 22 pounds 9 kg.
MINI HYD EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Ensure that all components of the engine oil pump are clean and free from wear and damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Illustration 1 g02367717
Illustration 2 g02367718
If necessary, lubricate the internal components for the assembly of the engine oil pump with clean engine oil. Install outer rotor (10) and front cover (9) to the housing of engine oil pump (8). Install bolts (13).
Tighten bolts (13) to a torque of 22 N m (195 lb in).
Ensure that dowel (11) and dowel (12) are correctly located in the housing of engine oil pump (8). Position the assembly of the engine oil pump onto the cylinder block. Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the holes in the cylinder block.
Install bolts (7). Tighten the bolts to a torque of 22 N m (195 lb in).
Check the backlash between idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Install suction pipe (1) and a new gasket (6) (not shown) to the assembly of engine oil pump (8).
Install bolts (5). Tighten the bolts to a torque to 22 N m (195 lb in).
If suction pipe (1) has a support bracket, follow Step 9.a through Step 9.d.
Install the components of support bracket (3). Ensure the correct location and orientation of the bracket and the retaining clip.
Install bolt (4).
Tighten bolt (4) and bolt (2) finger tight in order to align the components of the support bracket.
Tighten bolt (2) to a torque of 22 N m (195 lb in). Tighten bolt (4) to a torque of 44 N m (32 lb ft).End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Ensure that all components of the engine oil pump are clean and free from wear and damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Illustration 1 g02367717
Illustration 2 g02367718
If necessary, lubricate the internal components for the assembly of the engine oil pump with clean engine oil. Install outer rotor (10) and front cover (9) to the housing of engine oil pump (8). Install bolts (13).
Tighten bolts (13) to a torque of 22 N m (195 lb in).
Ensure that dowel (11) and dowel (12) are correctly located in the housing of engine oil pump (8). Position the assembly of the engine oil pump onto the cylinder block. Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the holes in the cylinder block.
Install bolts (7). Tighten the bolts to a torque of 22 N m (195 lb in).
Check the backlash between idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Install suction pipe (1) and a new gasket (6) (not shown) to the assembly of engine oil pump (8).
Install bolts (5). Tighten the bolts to a torque to 22 N m (195 lb in).
If suction pipe (1) has a support bracket, follow Step 9.a through Step 9.d.
Install the components of support bracket (3). Ensure the correct location and orientation of the bracket and the retaining clip.
Install bolt (4).
Tighten bolt (4) and bolt (2) finger tight in order to align the components of the support bracket.
Tighten bolt (2) to a torque of 22 N m (195 lb in). Tighten bolt (4) to a torque of 44 N m (32 lb ft).End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.
Caterpillar parts catalog:
Parts link Caterpillar catalog:
2604911
LINK
302.5C
302.5C
2498869
LINK
302.5C
302.5C
2920455
LINK AS
301.6C, 302.5C
301.6C, 302.5C
2641246
LINK & BEARING AS
301.6C
301.6C
2605539
LINK
301.6C
301.6C
2513318
LINK & BEARING AS
301.6C
301.6C
2774385
LINK AS
304C CR, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
304C CR, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
2663955
LINK
304C CR, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
304C CR, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
2663948
LINK & BEARING AS
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
2789935
LINK & BEARING AS
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
2814450
LINK AS
303.5C, 303.5E, 303C CR, 304C CR, 304E, 305.5E, 305C CR, 305E
303.5C, 303.5E, 303C CR, 304C CR, 304E, 305.5E, 305C CR, 305E
2743545
LINK AS
305.5, 305.5E, 306, 306E
305.5, 305.5E, 306, 306E