2726009 LINK AS-TRACK Caterpillar parts
D8R, D8R II, D8T
Rating:
Alternative (cross code) number:
CA2726009
272-6009
2726009
CA2726009
272-6009
2726009
Weight: 2585 pounds 1172 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
This part in 6 request:
Show.
This information for suppliers only!
2024-05-02
2023-09-11
2022-02-17
2022-01-12
2021-10-28
2020-04-15
Information:
Remove Rear Gear Group
start by:a) remove flywheel housing
3508 ONLY Before the flywheel housing is removed, the 3508 engine must be put in time to make sure the rear gear group is in alignment according to the rotation of the engine as shown. 1. Remove plate (1) to remove gear assembly (2) from the shaft. 2. Use tool group (A) and a press to remove bearing (3) from gear assembly (2).3. Use tool group (A) and a press to make a separation of the gears for gear assembly (2). 4. Remove the bolts to remove the shafts, gears (4) and the washers from the cylinder block. 5. Remove washers (6) and shafts (5) from gears (4). 6. Use tool group (A) and a press to remove the bearings from gears (4). Remove shaft (7) from engine. 7. Remove the bolts and remove gear (8) from the end of the crankshaft.Install Rear Gear Group
1. Put gear (1) in position on the end of the crankshaft and install the bolts. 2. Install shaft (2) on the cylinder block. 3. Use tool group (A) and a press to install the bearings in both gears (3) until the bearings are in the center of their bores. The bore in the bearing must be 75.00 0.053 mm (2.9528 .0021 in.) after assembly. 4. Put clean engine oil on the bearings and install shafts (5) in gears (3). Install washers (4) on the shafts. 5. Put gears (3) in position on the cylinder block and install the bolts to hold the gears in position. 6. Use tool group (A) and a press to install bearing (6) in gear assembly (7). The bore in bearing (6) must be 75.00 0.053 mm (2.9528 .0021 in.) after assembly. 7. Heat the larger gear of gear assembly (7) to a maximum temperature of 400° C (752° F) and install it on the smaller gear as shown.8. Put clean engine oil on the bearing and install gear assembly (7) on the shaft. Step 9 is for the 3508 Engine.9. Put clean engine oil on the bearing and install the gear assembly on the shaft. Make sure the marks on the gear assembly and the crankshaft gear are in alignment according to the rotation of the engine as shown.
3508 ONLY 10. Put plate (8) in position on gear assembly (7) and install the bolts.end by:a) install flywheel housing
start by:a) remove flywheel housing
3508 ONLY Before the flywheel housing is removed, the 3508 engine must be put in time to make sure the rear gear group is in alignment according to the rotation of the engine as shown. 1. Remove plate (1) to remove gear assembly (2) from the shaft. 2. Use tool group (A) and a press to remove bearing (3) from gear assembly (2).3. Use tool group (A) and a press to make a separation of the gears for gear assembly (2). 4. Remove the bolts to remove the shafts, gears (4) and the washers from the cylinder block. 5. Remove washers (6) and shafts (5) from gears (4). 6. Use tool group (A) and a press to remove the bearings from gears (4). Remove shaft (7) from engine. 7. Remove the bolts and remove gear (8) from the end of the crankshaft.Install Rear Gear Group
1. Put gear (1) in position on the end of the crankshaft and install the bolts. 2. Install shaft (2) on the cylinder block. 3. Use tool group (A) and a press to install the bearings in both gears (3) until the bearings are in the center of their bores. The bore in the bearing must be 75.00 0.053 mm (2.9528 .0021 in.) after assembly. 4. Put clean engine oil on the bearings and install shafts (5) in gears (3). Install washers (4) on the shafts. 5. Put gears (3) in position on the cylinder block and install the bolts to hold the gears in position. 6. Use tool group (A) and a press to install bearing (6) in gear assembly (7). The bore in bearing (6) must be 75.00 0.053 mm (2.9528 .0021 in.) after assembly. 7. Heat the larger gear of gear assembly (7) to a maximum temperature of 400° C (752° F) and install it on the smaller gear as shown.8. Put clean engine oil on the bearing and install gear assembly (7) on the shaft. Step 9 is for the 3508 Engine.9. Put clean engine oil on the bearing and install the gear assembly on the shaft. Make sure the marks on the gear assembly and the crankshaft gear are in alignment according to the rotation of the engine as shown.
3508 ONLY 10. Put plate (8) in position on gear assembly (7) and install the bolts.end by:a) install flywheel housing
Caterpillar SIS machinery equipment:
Caterpillar SIS
D8T TRACK-TYPE TRACTOR MB800001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR JJ500001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR DWJ00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR AW400001-UP (MACHINE) POWERED BY C15 ENGINE »
272-6009
LINK AS-TRACK
D8R Custom Parts Manual Track Type Tractor 6YZ00001-UP (MACHINE) »
272-6009
LINK AS-TRACK
D8R Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR 9EM00001-UP (MACHINE) POWERED BY 3406C Engine »
272-6009
LINK AS-TRACK
D8R Series II Track-Type Tractor 6YZ00001-UP (MACHINE) POWERED BY 3406E Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR KPZ00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR J8B00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR MLN00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR FCT00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR RJM00001-UP (MACHINE) POWERED BY 3406C Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR T5X00001-UP (MACHINE) POWERED BY 3406C Engine »
272-6009
LINK AS-TRACK
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 Engine »
272-6009
LINK AS-TRACK
D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C Engine »
272-6009
LINK AS-TRACK
Cat SIS web machinery list:
Parts link Caterpillar catalog:
2726010
LINK AS-TRACK
D8R, D8R II, D8T
D8R, D8R II, D8T
2433375
LINK AS
D8R, D8R II
D8R, D8R II
1058177
LINK AS
D8R
D8R
2024981
LINK AS
D8R, D8R II
D8R, D8R II
2433371
LINK AS
D8R, D8R II
D8R, D8R II
2393341
LINK AS
D8R, D8T
D8R, D8T
3045680
LINK-TRACK
D8R, D8T
D8R, D8T
2564902
LINK AS
D8R, D8T
D8R, D8T
2611175
LINK AS-WIPER
D10T, D11T, D8T, D9T
D10T, D11T, D8T, D9T
2611176
LINK AS
D10T, D11T, D8T, D9T
D10T, D11T, D8T, D9T
3811880
LINK GP-PITCH
D6T, D6T LGP, D6T LGPPAT, D6T XL
D6T, D6T LGP, D6T LGPPAT, D6T XL
3057356
LINK GP-GRAPPLE
325D MH
325D MH
2617526
LINK GP-BUCKET
994F, 994H
994F, 994H
2639240
LINK AS-TRACK
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
3248192
LINK GP-LADDER
776C, 777D, 785D
776C, 777D, 785D
2461039
LINK GP-STABILIZER
D9R, D9T
D9R, D9T
1082614
LINK AS-TRACK
D5H, D6M
D5H, D6M
9Q5636
LINK AS-TRACK
OEMS
OEMS
2450905
LINK GP-STEERING
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
3P1088
LINK AS-TRACK
955K, 955L, D6C, D6D
955K, 955L, D6C, D6D