AVSPARE.COM
parts catalog

LINK 2H9133 - Caterpillar



2H9133 LINK Caterpillar parts D337 LINK
Rating:
54
Alternative (cross code) number:
CA2H9133
2H-9133
2H9133
Caterpillar 2H9133 LINK

Buy LINK 2H9133 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 2H9133:

MARINE ENGINE  D337   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:

Start By:a. remove steering clutch hub couplingsb. remove pinion flangesc. remove drive shaft1. Remove the cover for the bevel gear compartment. 2. Remove nuts (1) from the bolts that hold the bevel gear on the shaft. 3. Remove the bolts that hold bearing cages (2) on the right and left sides of the bevel gear shaft. Install two3/8 - 16 NC forcing screws in the bearing cages. Tighten the forcing screws evenly and remove bearing cages (2) and shims. Keep the shims with their respective bearing cages for installation. 4. Remove the bolts that hold the pinion bearing cage assembly to the bevel gear case.5. Install two 3/8" - 16 NC forcing screws in the pinion bearing cage assembly. Tighten the forcing screws evenly and remove pinion bearing cage assembly (3) and shims. Keep the shims with the pinion bearing cage assembly for installation. 7. Move the bevel gear shaft away from the bevel gear.8. Remove bevel gear (5) and bevel gear shaft (4).9. Remove the bearing cups, O-ring seals and lip-type seals from the two bevel gear bearing cages. 10. Remove the bearing cones from the bevel gear shaft with tooling (A).
Typical Example11. Remove bolts (7) that hold the retainer on the pinion shaft flange (6). Keep the shims with the retainer for correct installation.
Typical Example12. Remove pinion bearing cage (8) from the pinion with tooling (A). Keep the puller attachment away from the inner bearing cone when tooling (A) is installed.
Typical Example13. Remove the O-ring seal and lip-type seal from pinion bearing cage (8).14. Remove the bearing cups from pinion bearing cage (8).15. Remove inner bearing cone (9) from pinion shaft (10) with tooling (A).Install Bevel Gear And Pinion
1. Lower the temperature of bearing cups (11). Install bearing cups (11) in the pinion bearing cage. 2. Lower the temperature of bearing cups (12). Install bearing cups (12) in bevel gear bearing cages (2). 3. Heat bearing cone (9) to a maximum temperature of 135°C (275°F). Install bearing cone (9) on the pinion shaft. Install the pinion shaft in pinion bearing cage (8). Install bearing cone (13) on the pinion shaft. Install O-ring seal (14). Install the lip-type seal in the pinion bearing cage with the lip of the seal toward the oil that is to be sealed.4. Install the flange, retainer and bolts. Tighten the bolts which will pull the bearing cone on to the pinion shaft. Turn the pinion shaft while the bolts are tightened until a small preload is felt. 5. Install tooling (B) as shown and check the end play in the pinion shaft. Add enough shims behind the retainer to get 0 to 0.05 mm (0 to .002 in.) end play in the pinion shaft. Install the O-ring, retainer, lock and bolts. 6. Heat bearing cones (15) to a maximum temperature of 135°C (275°F). Install bearing cones (15) on the bevel gear shaft.7. Put the bevel gear into position in the bevel gear case.8. Install the bevel gear shaft through the bevel

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455


Parts link Caterpillar catalog:

6B0165 LINK
3116, 3126, 3304, 3306, D315, D326F, D330A, D333A, D337, D342, D342C
9F2082 LINK ASSEM.
594, D337, D353C, D9E, D9G
1L1551 LINK
D337, D337F, D342, D397D
9F2082 LINK ASSEM.
594, D337, D353C, D9E, D9G
9F4387 LINK ASSEM.
D326F, D364, D375D
1L1551 LINK
D337, D337F, D342, D397D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.