AVSPARE.COM
parts catalog

LINK AS 3236562 - Caterpillar



3236562 LINK AS Caterpillar parts LINK
Rating:
11
Alternative (cross code) number:
CA3236562
323-6562
3236562
Caterpillar 3236562 LINK AS

Buy LINK AS 3236562 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Introduction
This information includes the following adjustment procedure:
Procedure to Assemble the Upper Hitch Bearings
Procedure to Install the Upper Hitch Pin
Procedure to Assemble the Lower Hitch Bearings
Procedure to Install the Lower Hitch PinProcedure to Assemble the Upper Hitch Bearings
Illustration 1 g03129021
Articulated Hitch
Illustration 2 g03129097
View B-B
(1) Seal. (2) Bolts (six). (3) Hard washers (six). (4) Upper bearing cap. (5) Shims. (6) Upper bearing cup. (7) Bearing cone. (8) Lower bearing cup. (9) Lower bearing cap. (10) Bearing cone. (11) Seal.
Apply 5P-3931 Thread Compound on the bearing bores in the frame.
Coat all bores with anti-seize compound.
Lubricate the sealing lips on seals (1) and (11) with the lubricant that is being sealed. Position seals (1) and (11), and press the seals into bearing caps (4) and (9).
Cool bearing cups (6) and (8) to a temperature of −50° 5°C (−58° 9°F).
Position lower bearing cap (9). Install three equally spaced bolts (2) and three hard washers (3) to keep lower bearing cap (9) in position. Tighten the bolts to 100 20 N m (74 150 lb ft).
Install lower bearing cup (8) into the bore of the housing. Drive the bearing cup downward to ensure contact with lower bearing cap (9).
Lubricate bearing cones (7) and (10) with oil and install the bearing cones.
Install upper bearing cup (6). Drive the bearing cup downward to ensure light contact pressure on the bearing cones.
Install shim (5), upper bearing cap (4), and three bolts (2) with hard washers (3). Install the bolts so that the bolts are 120° away from each other. Tighten the bolts by an equal amount. Torque to 100 20 N m (74 150 lb ft).
Adjust the rolling torque to rotate the bearing cones. As required, use shims (5) to attain the correct amount of rolling torque. The rolling torque should be not less than 2.3 N m (20.36 lb in). The rolling torque should not be greater than 13.6 N m (120.37 lb in).
Install all bolts (2) with hard washers (3). Tighten the bolts to 100 20 N m (74 150 lb ft).Procedure to Install the Upper Hitch Pin
Illustration 3 g03129216
View B-B
(12) Bolt. (13) Spacer. (14) Pin. (15) Upper sleeve bearing. (16) Lower sleeve bearing.
Install sleeve bearings (15) and (16) in the bores of the hitch.
Before pin (14) is installed, cool the pin to −50° 5°C (−58° 9°F).
Align the bores in the upper hitch and insert pin (14) into the bores.
Install bolt (12) and spacer (13) to lock the pin in place.
Tighten bolt (12) to 100 20 N m (74 150 lb ft).Procedure to Assemble the Lower Hitch Bearings
Illustration 4 g03129257
Articulated Hitch
Illustration 5 g03129260
View C-C
(1) Bolts (eight). (2) Hard washers (eight). (3) Seal. (4) Shims. (5) Upper bearing cap. (6) Upper bearing cup. (7) Upper bearing cone. (8) Lower bearing cup. (9) Lower bearing cone. (10) Lower bearing cap. (11) Seal.
Apply 5P-3931 Thread Compound on the bearing bores in the frame.
Coat all bores with anti-seize compound.
Lubricate seals (3) and (11) with the lubricant that is being sealed.


Parts link Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.