AVSPARE.COM
parts catalog

LINK AS 3692621 - Caterpillar


3692621 LINK AS Caterpillar parts 434F, 444F
Rating:
26
Alternative (cross code) number:
CA3692621
369-2621
3692621
Caterpillar 3692621 LINK AS
Weight: 85 pounds 38 kg.

Buy LINK AS 3692621 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$18.00
 

29 Mar 2020

-: -
CarPartsDepot, Old Style Flat Mirror Glass Left (Driver Side) Door View New Replacement, 369-2621 VW1323105
Part Number: VW1323105 || Dimensional Measurement: 6 1/2 x 3 3/4 INCH || Diagonal Measurement: 7 INCH || Placement On Vehicle: LEFT
Number on catalog scheme: 11
  For full view, you need register

Compatible equipment models: 3692621:

BACKHOE LOADER  434F   444F   Caterpillar

Information:


Illustration 1 g01592511
Schematic of the Lift Linkage Position Sensor
This diagnostic code is recorded when the Implement ECM determines that the voltage for the Lift Linkage Position Sensor is below normal. The Lift Linkage Position Sensor is a PWM sensor. The signal wire for the Lift Linkage Position Sensor connects to connector contact J2-32 (wire H710-PK(Pink)) of the ECM.The possible causes of this diagnostic code are listed:
A shorted harness
An open circuit in the power supply wiring for the lift linkage position sensor
A failed sensor
The ECM may have failed. This is unlikely.Note: Ensure that the diagnostic code is active and that the diagnostic code indicator is active.Note: The following procedure can create numerous related diagnostic codes. Reconnect all harnesses. Then, the related diagnostic codes will be shown as being NOT active. Complete the following procedure. Then, clear all of the related diagnostic codes.System Response:The machine response is listed:
The lift linkage will not work.
The tilt linkage will not work.
The active fault must be removed before the implement features will work properly.
Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position. Expected Result:The diagnostic code remains active.Results:
YES - The diagnostic code remains active. The sensor has not failed. The harness or the ECM may have failed. Proceed to Test Step 2.
NO - The diagnostic code is not active.Repair: The harness is correct and the ECM is operating properly. The sensor has failed. Replace the sensor.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the position sensor from the harness.
Disconnect the harness connector J1 and J2 from the ECM.
At the connector for the ECM, measure the resistance between contact J2-32 (wire H710-PK(Pink)) and ground in connector J1 and connector J2. Also, measure the resistance between contact J2-1 and frame ground. Expected Result:The resistance should be greater than 5000 ohms.Results:
YES - The resistance is greater than 5000 ohms. The harness is correct. Proceed to Test Step 3.
NO - The resistance is less than 5000 ohms.Repair: There is a short in the harness. The short is between the signal circuit (H710-PK(Pink)) and a ground source. Repair the harness or replace the harness.STOPTest Step 3. CHECK FOR +BATTERY
Do not disconnect the harness connector from the sensor.
Turn the key start switch and the disconnect switch to the ON position.
At the harness connector for the sensor, measure the voltage from contact A to contact B. Use the 7X-1710 Multimeter Probes and the 9U-7330 Digital Multimeter. Expected Result:The voltage is the system voltage.Results:
YES - The voltage is correct. The sensor is getting the proper voltage. Proceed to Test Step 4.
NO - The + battery circuit has failed.Repair: Repair the harness or replace the harness.STOPTest Step 4. CHECK IF THE DIAGNOSTIC CODE REMAINS
Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Observe the status of the diagnostic code.
Operate the machine.
Observe the status of the diagnostic code. Expected Result:The diagnostic code is active.Results:
YES - The diagnostic code

Caterpillar parts catalog:

Caterpillar parts catalog
434F Backhoe Loader LDH00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader LJJ00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader Side Shift JXR00001-UP (MACHINE) POWERED BY C4.4 Engine
434F Backhoe Loader MTR00001-UP (MACHINE) POWERED BY C4.4 Engine
444F2 Side Shift Backhoe Loader HWS00001-UP (MACHINE) POWERED BY C4.4 Engine
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader FBN00001-UP (MACHINE) POWERED BY C4.4 Engine
434F2 Side Shift Backhoe Loader LYK00001-UP (MACHINE) POWERED BY C4.4 Engine
444F2 Side Shift Backhoe Loader LYL00001-UP (MACHINE) POWERED BY C4.4 Engine
434F2 Side Shift Backhoe Loader HWR00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts link Caterpillar catalog:

1757877 LINK GP-SHIPPING
416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428C, 428D, 428E, 428F, 430F, 432D, 432E, 432F, 434E, 434F, 438C, 438D, 442D, 442E, 444E, 444F
3594737 LINK AS-BUCKET
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
7T1099 LINK
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
2747452 LINK-CONTROL
246C, 246D, 256C, 262C, 262C2, 262D, 272C, 272D, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 414E, 416E, 416F, 422E, 422F, 424B, 424B HD, 428E, 428F, ...
3305738 LINK
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3305739 LINK
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3594738 LINK AS
422E, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3455910 LINK AS
272D, 272D XHP, 299D, 299D XHP
3888174 LINK AS
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
3888173 LINK AS
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
3455108 LINK
272D, 272D XHP, 299D, 299D XHP
3455107 LINK
272D, 272D XHP, 299D, 299D XHP
3976723 LINK
424B, 424B HD
3786802 LINK
236D, 242D, 246D, 257D, 259D, 262D, 277D, 279D, 287D, 289D
3455619 LINK AS
262D, 287D, 289D
3887992 LINK AS
262D, 272D, 272D XHP, 287D, 289D, 299D, 299D XHP
3887778 LINK AS
242D, 257D, 259D
3456594 LINK AS
242D, 257D, 259D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.