3794768 LINK AS Caterpillar parts
324D L, 324E L, STIFF LINK
Rating:
Alternative (cross code) number:
CA3794768
379-4768
3794768
CA3794768
379-4768
3794768
Weight: 151 pounds 68 kg.
EXCAVATOR, THUMB,
Compatible equipment models: 3794768:
Number on catalog scheme:
9
For full view, you need register
Information:
Front Attachment Quick Disconnect Lines (If Equipped)
Before connecting or disconnecting quick disconnect plugs, follow the hints below.1. Stop the engine.2. Move all of the hydraulic attachment control levers to relieve the hose line hydraulic pressure.3. Return all levers to HOLD position.Connecting and Disconnecting Lines
1. Disconnect hydraulic lines to the tool being used, wipe off all foreign material.2. Remove the plugs and connect the lines.3. Install plugs in unused disconnects.Diverter Valve (If Equipped)
Failure to fully rotate the diverter valve handle to the auxiliary position can allow the coupler pins to retract and may release the tool, resulting in possible personal injury.Rotate the diverter valve handle 90° to the auxiliary position when the hoses from the tool are connected.
Connect the two hoses from the tool and rotate the diverter valve handle 90° to the auxiliary position. This shuts off the coupler cylinder circuit and allows til to only go to the tool circuit. To remove the tool, disconnect the two hoses from the tool and rotate the diverter valve handle 90° to the coupler position. This allows the oil to enter the coupler circuit.Bucket Operating Information
Typical Examples
For good operator vision and loader stability, carry the loaded bucket low, approximately 40 cm (15 in) above the ground.Utilize wait time to clean and level the work area.Maintain traction by avoiding excessive down pressure on the bucket.When working in hard material use bucket teeth, or bolt-on cutting edges.Be certain that the bucket used is appropriate for the work performed. Exceeding the machine limits will reduce the service life of the machine.Dozing and Dumping
Dozing
Do not doze with the bucket in the tilt forward position or bucket damage can result.
Keep the bucket bottom parallel to the ground when dozing.Dumping
To control dumping, move the tilt control lever to the DUMP position. Then, return to the HOLD position. Repeat until the bucket is empty.To keep dust away from the engine and maintain visibility, dump with the wind to your back.Use the bucket stops for maximum dumping angle.
Striking the stops unnecessarily and repetitively can result in accelerated wear and high maintenance cost of the loader linkage.
Bucket Loading from a Stockpile
1. Position the bucket parallel to, and just skimming, the ground. Drive the bucket straight into the pile.2. Move the control to the RAISE detent position as forward movement slows. Return to the HOLD position for additional crowding power.3. To "pump" in a heaped load, work the tilt control lever back and forth.4. When the bucket is loaded, move the tilt control to the TILT BACK position.5. When the tilt control lever is released to the HOLD position, the bucket will rise.6. Raise the bucket high enough to clear the material being loaded. Move the transmission control to REVERSE.7. Carry the loaded bucket approximately 40 cm (15 in) above the ground level.8. When reaching the dump area, move the lift control to the RAISE detent. The lift kickout will automatically return the lift control to HOLD.Bucket Loading Hauling Units
1. To reduce the loader turning and travel, position the hauling
Before connecting or disconnecting quick disconnect plugs, follow the hints below.1. Stop the engine.2. Move all of the hydraulic attachment control levers to relieve the hose line hydraulic pressure.3. Return all levers to HOLD position.Connecting and Disconnecting Lines
1. Disconnect hydraulic lines to the tool being used, wipe off all foreign material.2. Remove the plugs and connect the lines.3. Install plugs in unused disconnects.Diverter Valve (If Equipped)
Failure to fully rotate the diverter valve handle to the auxiliary position can allow the coupler pins to retract and may release the tool, resulting in possible personal injury.Rotate the diverter valve handle 90° to the auxiliary position when the hoses from the tool are connected.
Connect the two hoses from the tool and rotate the diverter valve handle 90° to the auxiliary position. This shuts off the coupler cylinder circuit and allows til to only go to the tool circuit. To remove the tool, disconnect the two hoses from the tool and rotate the diverter valve handle 90° to the coupler position. This allows the oil to enter the coupler circuit.Bucket Operating Information
Typical Examples
For good operator vision and loader stability, carry the loaded bucket low, approximately 40 cm (15 in) above the ground.Utilize wait time to clean and level the work area.Maintain traction by avoiding excessive down pressure on the bucket.When working in hard material use bucket teeth, or bolt-on cutting edges.Be certain that the bucket used is appropriate for the work performed. Exceeding the machine limits will reduce the service life of the machine.Dozing and Dumping
Dozing
Do not doze with the bucket in the tilt forward position or bucket damage can result.
Keep the bucket bottom parallel to the ground when dozing.Dumping
To control dumping, move the tilt control lever to the DUMP position. Then, return to the HOLD position. Repeat until the bucket is empty.To keep dust away from the engine and maintain visibility, dump with the wind to your back.Use the bucket stops for maximum dumping angle.
Striking the stops unnecessarily and repetitively can result in accelerated wear and high maintenance cost of the loader linkage.
Bucket Loading from a Stockpile
1. Position the bucket parallel to, and just skimming, the ground. Drive the bucket straight into the pile.2. Move the control to the RAISE detent position as forward movement slows. Return to the HOLD position for additional crowding power.3. To "pump" in a heaped load, work the tilt control lever back and forth.4. When the bucket is loaded, move the tilt control to the TILT BACK position.5. When the tilt control lever is released to the HOLD position, the bucket will rise.6. Raise the bucket high enough to clear the material being loaded. Move the transmission control to REVERSE.7. Carry the loaded bucket approximately 40 cm (15 in) above the ground level.8. When reaching the dump area, move the lift control to the RAISE detent. The lift kickout will automatically return the lift control to HOLD.Bucket Loading Hauling Units
1. To reduce the loader turning and travel, position the hauling
Caterpillar parts catalog:
Parts link Caterpillar catalog:
322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D L, 324D LN, 326D L, 329D L, 345D L, OEMS
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U, 320C, 320C F...
1090, 1190T, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320B U,...
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 325D,...
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 325D,...
2602463
LINK & BEARING AS
324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN
324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN
2824548
LINK AS
324D, 324D L, 324D LN
324D, 324D L, 324D LN
3782348
LINK AS
STIFF LINK
STIFF LINK
3782438
LINK AS
STIFF LINK
STIFF LINK
3782472
LINK AS
STIFF LINK
STIFF LINK
2357759
LINK & BEARING AS
324D, 329D LN, 330D L, 336D, 336D L, 336D LN, 336D2, 336E, 336E LN, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E
324D, 329D LN, 330D L, 336D, 336D L, 336D LN, 336D2, 336E, 336E LN, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
2481842
LINK & BEARING AS
320E, 323D L, 325D L, 329D, 329D L, 329E
320E, 323D L, 325D L, 329D, 329D L, 329E
3197045
LINK AS
3197042, 320D
3197042, 320D
3813809
LINK AS
2864C, 586C, BR624, HM825, MD-250, MR-244
2864C, 586C, BR624, HM825, MD-250, MR-244
3756872
LINK
320D, 320D2
320D, 320D2
3756871
LINK AS
320D, 320D2
320D, 320D2
3657157
LINK & BEARING AS
320E, 320E RR
320E, 320E RR
2792738
LINK AS
324E
324E
2792737
LINK AS
324E
324E
4225504
LINK AS-TRACK
320E L
320E L