3P1088 LINK AS-TRACK Caterpillar parts
955K, 955L, D6C, D6D
Rating:
Alternative (cross code) number:
CA3P1088
3P-1088
3P1088
CA3P1088
3P-1088
3P1088
Weight: 1190 pounds 539 kg.
TRACK LOADER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$3,398.25
16 Jun 2023
US: Florida-Parts-Z
3P1088 - Link AS-Track for Caterpillar (CAT) !!!Free Shipping!!!
FIRST PRICE PARTS
FIRST PRICE PARTS
$2,729.65
16 Feb 2022
US: Florida-Parts-Z
3P1088 - Link AS-Track for Caterpillar (CAT) !!!Free Shipping!!!
FIRST PRICE PARTS
FIRST PRICE PARTS
Information:
Remove Pistons
start by:a) remove spacer platesb) remove piston cooling jets1. If necessary, remove the cover from the front right side of the flywheel housing and use tool (A) to turn the engine flywheel until all four of bolts (1) can be removed. 2. Remove bolts (1) and bearing cap (2) from the connecting rod. 3. Push the piston up until the piston rings are clear of the cylinder liner. Remove pistons (3) and the connecting rods. Put identification on each piston as to its location for correct installation and alignment. Keep each bearing cap with its connecting rod. 4. Use tool (B) and remove the rings that hold piston pin (4) in position. Remove pin (4) and remove piston (3) from connecting rod (5).5. Remove the bearings from the bearing cap and connecting rod (5). 6. Use tool (C) to remove piston rings (6) from piston (3).Install Pistons
1. Clean the ring grooves in the piston. 2. Use tool (A) to install the oil ring on piston (1). Make sure the oil ring spring ends are 180° apart from the ring end gap.3. Use tool (A) to install the two compression rings on piston (1). Make sure the sides with the "UP" marks are toward the top of the piston and all three ring end gaps are 120° apart after installation. 4. Put clean engine oil on pin (3), the pin bearing in rod (2) and the pin bore in piston (1). Put rod (2) in position in piston (1) and install pin (3). Use tool (B) to install rings (4) on each side of pin (3).5. Install the upper half of the connecting rod bearing in the connecting rod and put clean engine oil on it. Make sure the tab on the back of the bearing fits in the groove of the rod. 6. Put clean engine oil on the piston rings and cylinder liner bore. Use tool (D) to put the piston rings under compression and install the pistons and connecting rods in the cylinder liners.
Make sure the piston is installed with the side of the connecting rod that has the chamfer in the rod bearing bore next to the crankshaft thrust surface. The side with the square shoulder for the connecting rod bearing bore must be next to the other connecting rod on the same crankshaft journal.
7. Install the lower half of the connecting rod bearing in cap (5) and put clean engine oil on it. Make sure the tab on the back of the bearing fits in the groove of the cap.8. See INSTALL CONNECTING ROD BEARINGS for the procedure to install the connecting rod caps and to check the bearing clearance.9. Check the side clearance between two connecting rods on the same crankshaft journal. The clearance must be 0.85 0.23 mm (.335 .0091 in.) for the 12 cylinder and 0.900 .282 mm (.0354 .0111 in) for the 8 cylinder.end by:a) install cooling jetsb) install spacer plates
start by:a) remove spacer platesb) remove piston cooling jets1. If necessary, remove the cover from the front right side of the flywheel housing and use tool (A) to turn the engine flywheel until all four of bolts (1) can be removed. 2. Remove bolts (1) and bearing cap (2) from the connecting rod. 3. Push the piston up until the piston rings are clear of the cylinder liner. Remove pistons (3) and the connecting rods. Put identification on each piston as to its location for correct installation and alignment. Keep each bearing cap with its connecting rod. 4. Use tool (B) and remove the rings that hold piston pin (4) in position. Remove pin (4) and remove piston (3) from connecting rod (5).5. Remove the bearings from the bearing cap and connecting rod (5). 6. Use tool (C) to remove piston rings (6) from piston (3).Install Pistons
1. Clean the ring grooves in the piston. 2. Use tool (A) to install the oil ring on piston (1). Make sure the oil ring spring ends are 180° apart from the ring end gap.3. Use tool (A) to install the two compression rings on piston (1). Make sure the sides with the "UP" marks are toward the top of the piston and all three ring end gaps are 120° apart after installation. 4. Put clean engine oil on pin (3), the pin bearing in rod (2) and the pin bore in piston (1). Put rod (2) in position in piston (1) and install pin (3). Use tool (B) to install rings (4) on each side of pin (3).5. Install the upper half of the connecting rod bearing in the connecting rod and put clean engine oil on it. Make sure the tab on the back of the bearing fits in the groove of the rod. 6. Put clean engine oil on the piston rings and cylinder liner bore. Use tool (D) to put the piston rings under compression and install the pistons and connecting rods in the cylinder liners.
Make sure the piston is installed with the side of the connecting rod that has the chamfer in the rod bearing bore next to the crankshaft thrust surface. The side with the square shoulder for the connecting rod bearing bore must be next to the other connecting rod on the same crankshaft journal.
7. Install the lower half of the connecting rod bearing in cap (5) and put clean engine oil on it. Make sure the tab on the back of the bearing fits in the groove of the cap.8. See INSTALL CONNECTING ROD BEARINGS for the procedure to install the connecting rod caps and to check the bearing clearance.9. Check the side clearance between two connecting rods on the same crankshaft journal. The clearance must be 0.85 0.23 mm (.335 .0091 in.) for the 12 cylinder and 0.900 .282 mm (.0354 .0111 in) for the 8 cylinder.end by:a) install cooling jetsb) install spacer plates
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts link Caterpillar catalog:
3P1118
LINK AS-TRACK
955K, 955L, D6C, D6D, D6D SR
955K, 955L, D6C, D6D, D6D SR
3P1120
LINK AS-TRACK
D6D, D6E, D6E SR, D6G SR
D6D, D6E, D6E SR, D6G SR
3P7153
LINK-TRACK-RH
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
3P7154
LINK-TRACK-LH
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
225, 951B, 953, 955K, 955L, D5, D5B, D5E, FB221, OEMS
2H5048
LINK
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
2H5046
LINK
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
561B, 561C, 955C, 977D, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR, D7F, D7G
6P3683
LINK ASSEM.
D6C, D8H, D8K
D6C, D8H, D8K
1V7077
LINK ASSEM.
955L
955L
9M9042
LINK
D6C
D6C
9M9041
LINK
D6C
D6C
7M8537
LINK
D6C
D6C
2726009
LINK AS-TRACK
D8R, D8R II, D8T
D8R, D8R II, D8T
3811880
LINK GP-PITCH
D6T, D6T LGP, D6T LGPPAT, D6T XL
D6T, D6T LGP, D6T LGPPAT, D6T XL
3057356
LINK GP-GRAPPLE
325D MH
325D MH
2617526
LINK GP-BUCKET
994F, 994H
994F, 994H
2639240
LINK AS-TRACK
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E
2461039
LINK GP-STABILIZER
D9R, D9T
D9R, D9T
1082614
LINK AS-TRACK
D5H, D6M
D5H, D6M
9Q5636
LINK AS-TRACK
OEMS
OEMS
2450905
LINK GP-STEERING
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ