AVSPARE.COM
parts catalog

LINK AS 4Z8715 - Caterpillar



4Z8715 LINK AS Caterpillar parts LINK
Rating:
11
Alternative (cross code) number:
CA4Z8715
4Z-8715
4Z8715
Caterpillar 4Z8715 LINK AS
Weight: 220 pounds 99 kg.

Buy LINK AS 4Z8715 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Note: The machine has the ability to split, ensure wheel chocks are in place.Note: Cleanliness is an important factor. Before the installation procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Illustration 1 g00783742
Install O-ring seal (21) onto bearing carrier (8).
Use Tooling (A) in order to install new lip seal (20) into the bearing carrier (8). Fill in 1/3 of the cavity bearing carrier (8) with Tooling (C) in order to lubricate lip seal (20).
Illustration 2 g00783741
View from the hitch area.
Position bearing carrier (8) onto the hitch tube. Install bolts (19) in order to connect bearing carrier (8) to the hitch tube.
Illustration 3 g01196527
Raise the temperature of bearing (16) in order to install bearing (16) onto hitch drive shaft (14). Turn over hitch drive shaft (14) and install retaining ring (15) that is used to secure bearing (16) to bearing carrier (4) in step 6. Repeat the procedure in order to install the bearing onto the opposite end of the hitch drive shaft (14).
Illustration 4 g01196525
Use Tooling (A) in order to install new lip seal (18) into bearing carrier (4). Fill in 1/3 of the cavity bearing carrier (4) with Tooling (C) in order to lubricate lip seal (18).
Illustration 5 g01196521
Install O-ring seal (17) onto bearing carrier (4). Install hitch drive shaft (14) and roller bearing (16) into bearing carrier (4). Use Tooling (B) in order to install retaining ring (15) into bearing carrier (4).
Illustration 6 g00783239
Coat the splines at the end of hitch drive shaft (14) with grease. Install shaft yoke (13) and the O-ring seal onto hitch drive shaft (14). Install bolt (11) and washer (12) in order to secure shaft yoke (13) to the bearing carrier (4) and the hitch drive shaft (14).
Illustration 7 g00783219
Typical Example
View from the underside of the rear frame.
Use two people in order to install bearing carrier (4) and hitch drive shaft (14) to the hitch tube. The weight of bearing carrier (4) and hitch drive shaft (14) is approximately 45 kg (100 lb).
Install bolts (9) in order to secure bearing carrier (4) to the hitch tube. Note: Ensure that the two remaining bolt holes in the bearing carrier are adjacent to each other for installation of the locking plate in step 13.
Note the orientation of lip seal (10), and install lip seal (10) onto bearing housing (4).
Illustration 8 g00783315
Coat the splines at the end of hitch drive shaft (14) with grease. Install shaft yoke (7) and the O-ring seal onto hitch drive shaft (14). Install bolt (5) and washer (6) in order to connect the shaft yoke (7) to bearing carrier (8) and hitch drive shaft (14).
Illustration 9 g03861541
Apply Tooling (D) to the threads of thrust flange (3). Install thrust flange (3) onto bearing carrier (4). Insert locking plate (2) and a suitable 3/4 inch breaker bar into the holes in thrust flange (3) in order to tighten the thrust flange. Note: For the correct setting procedure, refer to Operation and Maintenance Manual, "Oscillating Hitch - Adjust".
Illustration 10 g03861545
Install


Parts link Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.