AVSPARE.COM
parts catalog

LINK GP-STABILIZER 4Z9385 - Caterpillar



4Z9385 LINK GP-STABILIZER Caterpillar parts D8R, D8R II LINK
Rating:
34
Alternative (cross code) number:
CA4Z9385
4Z-9385
4Z9385
Caterpillar 4Z9385 LINK GP-STABILIZER
Weight: 25 pounds 11 kg.

Buy LINK GP-STABILIZER 4Z9385 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z9385:

TRACK-TYPE TRACTOR  D8R   D8R II   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Probable Causes
Diagnostic codes
Event codes
Derates
Cold mode and/or starting aids
Engine parameters
Throttle signal
Decelerator pedal
Intake manifold pressure sensor and atmospheric pressure sensor
Air inlet and exhaust system
Fuel supply
Cylinder performance
Electrical connectors
Accessory equipmentRecommended Actions
Diagnostic Codes, Event Codes and Derates
Certain diagnostic codes, event codes and/or derates may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.If this application supports engine derates, use Cat ET to check for logged derates. Refer to Troubleshooting, "Event Code List" for the specific events that are applicable to this application. A status screen on Cat ET will display a derate if a derate is active.Cold Mode and/or Starting Aids
Connect Cat ET to the service tool connector. Verify that the engine has exited cold mode. This may limit engine speed.Check the operation of the air inlet heater (if applicable). Ensure that the air inlet heater is operating properly. For additional information on troubleshooting electrical problems with the air inlet heater, refer to Troubleshooting, "Air Inlet Heater - Test".Check the operation of the ether injection system (if applicable). Ensure that the ether injection system is operating properly. For additional information on troubleshooting electrical problems with the ether injection system, refer to ON position. For additional information, refer to Troubleshooting, "Ether Starting Aid - Test".Engine Parameters
Verify that the correct engine parameters are being used.Throttle Signal
Connect Cat ET to the service tool connector. View the status for the throttle position on the status screen. Operate the throttle from the low idle position to the high idle position. The status should be 0 percent at low idle and the status should be 100 percent at high idle. If the status can not operate in the full range, refer to Troubleshooting, "Throttle Position Sensor - Calibrate".Diagnostic codes that are related to the J1939 data link will prevent correct operation of the throttle if the throttle position is transmitted over the data link. If there is a problem with the data link, the engine will remain at low idle until the data link is repaired.Decelerator Pedal
Monitor the decelerator pedal on Cat ET. Verify that the decelerator pedal is operating properly.Intake Manifold Pressure Sensor and Atmospheric Pressure Sensor
Monitor the status of "Fuel Position", of "Rated Fuel Limit", and of "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters must reflect the information below.
Table 1
"Fuel Position" = "Rated Fuel Limit"
and
"Fuel Position" < "FRC Fuel Limit"    If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.
Use Cat ET in order to monitor the status of the "Boost Pressure". With the engine stopped, the correct "Boost Pressure" is 0 kPa (0 psi).
Start the engine and monitor the status of "Boost Pressure" while you vary the engine speed. Ensure that the pressure reading is fluctuating with the engine speed.
Use Cat ET in order to check the status of the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D8R Custom Parts Manual Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine
D8R Custom Parts Manual Track Type Tractor 6YZ00001-UP (MACHINE)


Parts link Caterpillar catalog:

2726010 LINK AS-TRACK
D8R, D8R II, D8T
8E4059 LINK-TRACK MASTER
D8N, D8R, D8R II, D8T
2649766 LINK AS-TRACK BOX
D5K LGP, D6K, D6K LGP
1047425 LINK GP-PITCH
D5M, D5N, D6K, D6K LGP, D6K XL
4236758 LINK GP
308E, 308E2 CR
3522831 LINK GP-UPPER
770G, 770G OEM, 772G, 772G OEM
1231194 LINK GP-STABILIZER
825G, 825G II, 825H, 825K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.