5426613 LINK AS-TRACK Caterpillar parts
Rating:
Alternative (cross code) number:
CA5426613
542-6613
5426613
CA5426613
542-6613
5426613
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
#US Replacement part for '06 - '14 07 for Sportsman 500 550 IDLE SPEED CONTROL for Polaris FAST carbPart#5426613
Generic NOTE - Package included: 1 Set ONLY. Please check all carefully (photos and model) and make sure it will compatible with your original one. || Manufacturer Part Number: for Sportsman 550 500
Generic NOTE - Package included: 1 Set ONLY. Please check all carefully (photos and model) and make sure it will compatible with your original one. || Manufacturer Part Number: for Sportsman 550 500
Number on catalog scheme:
For full view, you need register
Information:
harness is not correct. Repair: Repair the wiring harness or replace the wiring harness. Proceed to Test Step 10.Test Step 4. CHECK THE CONTINUITY OF THE ECS (TERMINAL 7).
There is a jumper wire on the ECS that attaches terminal 6 to terminal 9. Remove this wire.
Place the ECS in the "OFF/RESET" position.Note: On 3456 engines, remove the time delay relay (TDR) before performing the next step.
Measure the resistance between terminal 6 of the ECS and terminal 7 of the ECS with an ohmmeter. Continue to measure the resistance between terminal 6 of the ECS and terminal 7 of the ECS while the ECS is rotated to the AUTO, MANUAL, and STOP positions. Take note of the readings.Expected Result:When the ECS is in the OFF/RESET position, there should be less than 5 Ohms resistance between terminal 7 of the ECS and terminal 6 of the ECS. More than 5000 Ohms should exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions.Results:
OK - Less than 5 Ohms of resistance exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the OFF/RESET position. More than 5000 Ohms exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions. The ECS has not failed. Proceed to Test Step 5.
NOT OK - More than 5 Ohms of resistance exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the OFF/RESET position. Less than 5000 Ohms exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions. The ECS has failed. Repair: Replace the ECS. Reinstall the jumper wire. Proceed to Test Step 10.Test Step 5. CHECK THE CONTINUITY OF THE ECS (TERMINAL 8).
There is a jumper wire on the ECS that attaches terminal 6 to terminal 9. Remove this wire.Expected Result:Less than 5 Ohms of resistance should exist
There is a jumper wire on the ECS that attaches terminal 6 to terminal 9. Remove this wire.
Place the ECS in the "OFF/RESET" position.Note: On 3456 engines, remove the time delay relay (TDR) before performing the next step.
Measure the resistance between terminal 6 of the ECS and terminal 7 of the ECS with an ohmmeter. Continue to measure the resistance between terminal 6 of the ECS and terminal 7 of the ECS while the ECS is rotated to the AUTO, MANUAL, and STOP positions. Take note of the readings.Expected Result:When the ECS is in the OFF/RESET position, there should be less than 5 Ohms resistance between terminal 7 of the ECS and terminal 6 of the ECS. More than 5000 Ohms should exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions.Results:
OK - Less than 5 Ohms of resistance exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the OFF/RESET position. More than 5000 Ohms exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions. The ECS has not failed. Proceed to Test Step 5.
NOT OK - More than 5 Ohms of resistance exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the OFF/RESET position. Less than 5000 Ohms exist between terminal 7 of the ECS and terminal 6 of the ECS when the ECS is in the AUTO, MANUAL, or STOP positions. The ECS has failed. Repair: Replace the ECS. Reinstall the jumper wire. Proceed to Test Step 10.Test Step 5. CHECK THE CONTINUITY OF THE ECS (TERMINAL 8).
There is a jumper wire on the ECS that attaches terminal 6 to terminal 9. Remove this wire.Expected Result:Less than 5 Ohms of resistance should exist
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts link Caterpillar catalog:
5418741
LINK-TRACK
Caterpillar
Caterpillar
5418740
LINK-TRACK
Caterpillar
Caterpillar
5418739
LINK-TRACK MASTER
Caterpillar
Caterpillar
5418738
LINK-TRACK MASTER
Caterpillar
Caterpillar
5331640
LINK AS
Caterpillar
Caterpillar
5331638
LINK AS
Caterpillar
Caterpillar
3894647
LINK GP-STEERING FRAME LOCK
Caterpillar
Caterpillar
3894587
LINK GP-BUCKET
Caterpillar
Caterpillar
3734004
LINK GP-TILT
Caterpillar
Caterpillar
3733999
LINK GP-TILT
Caterpillar
Caterpillar
5463041
LINK
Caterpillar
Caterpillar
5426614
LINK AS-TRACK
Caterpillar
Caterpillar