6Y1140 LINK AS-TRACK Caterpillar parts
D7H
Rating:
Alternative (cross code) number:
CA6Y1140
6Y-1140
6Y1140
CA6Y1140
6Y-1140
6Y1140
Weight: 2000 pounds 907 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 6Y1140:
Information:
Parameter Descriptions
Rating Number
This machine engine has two power ratings. The ECM is programmed to automatically change the power rating of the engine when certain conditions are present. The conditions are specified in two features that are available for the machine.The status of the power rating is dependent on the status of the transmission gear and the implement controls.The "Rating Number" parameter provides a way to view the information on each rating. Changing this parameter does not select the engine power rating.Equipment ID
"Equipment ID" allows the customer to enter a description into the Electronic Control Module (ECM) in order to identify the machine. A maximum of 17 characters may be entered in the field. This parameter is only for reference by the customer. This parameter is not required.Engine Serial Number
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate. If the ECM is replaced, the engine serial number from the engine information plate must be programmed into the new ECM.Note: When you are requesting factory passwords, always use the engine serial number that is programmed in the ECM.FLS (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Factory passwords are required in order to change this parameter.FTS (Full Torque Setting)
"FTS" is similar to "FLS". Factory passwords are required in order to change this parameter.Ether Solenoid Configuration
Program the "Ether Solenoid Configuration" to "Continuous Flow" if an ether injection system is installed on the engine.System Battery Voltage Low Elevated Idle
Set the "System Battery Voltage Low Elevated Idle" parameter to "Enabled" in order to help maintain a proper charge on the batteries when electrical accessories have been added by the customer. This feature increases engine rpm to 1000 when the following conditions are met:
The parameter is set to "Enabled".
System battery voltage is less than 24.5 VDC for five minutes.
The throttle pedal position is below 25 percent for five minutes.
The machine is not in gear.
The parking brake is set.The engine rpm will return to low idle when any of the following conditions occur:
The parking brake is released.
The transmission is not in neutral.
The throttle is above 25 percent.Parameters Worksheet
Table 2
Engine Parameters
Rating Number
Rated Power
Rated Peak Torque
Top Engine Speed Range
Test Spec
Equipment ID
Engine Serial Number
ECM Serial Number
ECM Part Number
Software Group Part Number
Software Group Release Date
Software Group Description
FLS
FTS
Ether Solenoid Configuration
System Battery Voltage Low Elevated Idle
Total Tattletale
Injector Serial Numbers
Cylinder 1
Cylinder 2
Cylinder 3
Cylinder 4
Cylinder 5
Cylinder 6
Rating Number
This machine engine has two power ratings. The ECM is programmed to automatically change the power rating of the engine when certain conditions are present. The conditions are specified in two features that are available for the machine.The status of the power rating is dependent on the status of the transmission gear and the implement controls.The "Rating Number" parameter provides a way to view the information on each rating. Changing this parameter does not select the engine power rating.Equipment ID
"Equipment ID" allows the customer to enter a description into the Electronic Control Module (ECM) in order to identify the machine. A maximum of 17 characters may be entered in the field. This parameter is only for reference by the customer. This parameter is not required.Engine Serial Number
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate. If the ECM is replaced, the engine serial number from the engine information plate must be programmed into the new ECM.Note: When you are requesting factory passwords, always use the engine serial number that is programmed in the ECM.FLS (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Factory passwords are required in order to change this parameter.FTS (Full Torque Setting)
"FTS" is similar to "FLS". Factory passwords are required in order to change this parameter.Ether Solenoid Configuration
Program the "Ether Solenoid Configuration" to "Continuous Flow" if an ether injection system is installed on the engine.System Battery Voltage Low Elevated Idle
Set the "System Battery Voltage Low Elevated Idle" parameter to "Enabled" in order to help maintain a proper charge on the batteries when electrical accessories have been added by the customer. This feature increases engine rpm to 1000 when the following conditions are met:
The parameter is set to "Enabled".
System battery voltage is less than 24.5 VDC for five minutes.
The throttle pedal position is below 25 percent for five minutes.
The machine is not in gear.
The parking brake is set.The engine rpm will return to low idle when any of the following conditions occur:
The parking brake is released.
The transmission is not in neutral.
The throttle is above 25 percent.Parameters Worksheet
Table 2
Engine Parameters
Rating Number
Rated Power
Rated Peak Torque
Top Engine Speed Range
Test Spec
Equipment ID
Engine Serial Number
ECM Serial Number
ECM Part Number
Software Group Part Number
Software Group Release Date
Software Group Description
FLS
FTS
Ether Solenoid Configuration
System Battery Voltage Low Elevated Idle
Total Tattletale
Injector Serial Numbers
Cylinder 1
Cylinder 2
Cylinder 3
Cylinder 4
Cylinder 5
Cylinder 6
Caterpillar SIS machinery equipment:
Caterpillar SIS
D7H & D7H LGP TRACTORS / POWER SHIFT / 79Z00001-03999 (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H & D7H LGP SERIES II TRACTORS / POWERSHIFT / 79Z04000-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H & D7H LGP SERIES II TRACTORS / POWERSHIFT / 4AB04000-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H & D7H LGP SERIES II TRACTORS / DIRECT DRIVE / 2SB04000-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H & D7H LGP SERIES II TRACTORS / POWERSHIFT / 2RG04000-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H & D7H LGP TRACTOR / DIRECT DRIVE / 2SB00001-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
D7H TRACK-TYPE TRACTOR / POWERSHIFT / 4AB00001-UP (MACHINE) POWERED BY 3306 ENGINE »
6Y-1140
LINK AS-TRACK
Caterpillar parts catalog:
Parts link Caterpillar catalog:
1156301
LINK AS-TRACK
D7E, D7H, D7R, D7R II, D7R XR
D7E, D7H, D7R, D7R II, D7R XR
1156303
LINK AS-TRACK
D7H, D7R, D7R II, D7R XR
D7H, D7R, D7R II, D7R XR
1156302
LINK AS-TRACK
572R, 572R II, D7H, D7R, D7R II, D7R XR
572R, 572R II, D7H, D7R, D7R II, D7R XR
7T1099
LINK
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
7T5923
LINK
AP-600D, AP-655D, D7H
AP-600D, AP-655D, D7H
2924773
LINK GP-GRAPPLE
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
1156302
LINK AS-TRACK
572R, 572R II, D7H, D7R, D7R II, D7R XR
572R, 572R II, D7H, D7R, D7R II, D7R XR
2352525
LINK AS-TRACK
D4H, D4H XL, D5M, D5N, D6K LGP
D4H, D4H XL, D5M, D5N, D6K LGP
1806185
LINK GP-TOP
35, 45, 55
35, 45, 55
3455115
LINK GP-COUPLER
272D, 272D XHP, 299D, 299D XHP
272D, 272D XHP, 299D, 299D XHP
1187301
LINK AS-TRACK
330B, 330B L, OEMS
330B, 330B L, OEMS
2924066
LINK GP-GRAPPLE
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
2924064
LINK GP-GRAPPLE
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
GSH15, GSH15-60, GSH22B, GSH9, GSH9B
1959343
LINK AS-TRACK
318C, 322B, 322C, 324D, 324D L
318C, 322B, 322C, 324D, 324D L
3116644
LINK AS-TRACK
D6K, D6K LGP, D6K XL, D6K2 LGP, PL61
D6K, D6K LGP, D6K XL, D6K2 LGP, PL61
1082616
LINK AS-TRACK
D4H, D4H XL, D5M
D4H, D4H XL, D5M