8E2360 LINK-TRACK MASTER Caterpillar parts
D6H, D6H II, D6H XL, D6H XR
Rating:
Alternative (cross code) number:
CA8E2360
8E-2360
8E2360
CA8E2360
8E-2360
8E2360
Weight: 5 pounds 2 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
6
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7B-7974 Piston Ring Expander Gp 1 Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01222629
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position top piston ring (1), intermediate piston ring (2), and oil control piston ring (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of top piston ring (1), intermediate piston ring (2), and oil control piston ring (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (7) and install the connecting rod pin. Install pin retainers (5) with Tooling (A).
Install upper connecting rod bearing (8) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (9) in connecting rod bearing cap (10). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7B-7974 Piston Ring Expander Gp 1 Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01222629
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position top piston ring (1), intermediate piston ring (2), and oil control piston ring (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of top piston ring (1), intermediate piston ring (2), and oil control piston ring (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (7) and install the connecting rod pin. Install pin retainers (5) with Tooling (A).
Install upper connecting rod bearing (8) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (9) in connecting rod bearing cap (10). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Caterpillar parts catalog:
Parts link Caterpillar catalog:
D6H, D6H XL, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
527, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
D6H, D6R, D6R II, D6R III, D6T
D6H, D6H XL, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6H XR, D6R, D6R II
216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 236B3, 242B, 242B3, 246C, 246D, 247, 247B, 247B3, 248, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, ...
14E, 16, 572G, 621, 621B, 627, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 633C, 637B, 637D, 637E, 637G, 641B, 657B, 769C, 777, 824B, 825B, 931B, 950, 955K, 955L, 980B, 992, D3B, D4H, D5, D5B, D5H, ...
D4H, D5H, D6F SR, D6G SR, D6H, D7H
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR
2282738
LINK-TRACK MASTER
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II
2282735
LINK-TRACK
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II
8E2357
LINK-TRACK MASTER
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR
8E2358
LINK-TRACK MASTER
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR
8E2359
LINK-TRACK MASTER
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR