AVSPARE.COM
parts catalog

LINKAGE AR-BUCKET 3904349 - Caterpillar



3904349 LINKAGE AR-BUCKET Caterpillar parts 308E CR LINKAGE
Rating:
23
Alternative (cross code) number:
CA3904349
390-4349
3904349
Caterpillar 3904349 LINKAGE AR-BUCKET

Buy LINKAGE AR-BUCKET 3904349 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compatible equipment models: 3904349:

MINI HYD EXCAVATOR  308E CR   Caterpillar
  For full view, you need register

Information:


Illustration 1 g00796965
Place "CB1" in the OFF position in order to remove the power.
Disconnect the speed sensor from terminals 4 and 5 of the tachometer.
Connect the positive lead of the signal generator to terminal 4 of the tachometer and to terminal 5 of the tachometer.
Place "CB1" in the ON position.
Measure the voltage at terminal +4 of the tachometer with respect to terminal −5 of the tachometer. The voltage should be greater than 3.5 volts.
Check the following components and refer to Table 1.
Engine Crank Terminate Relay
Engine Crank Terminate Time Delay Relay
Engine Oil Step Relay
Engine Overspeed RelaySet the 163-0096 Diagnostic and Calibration Tool to 10 Hz below the setpoint that is desired. The output for that setting should remain OFF. Change the settings to 10 Hz above the setpoint that is desired. The output terminal of the tachometer should have 24 VDC with respect to terminal 2. The output of the relay for that setting should turn on.
Table 1
Rated Speed    Crank Termination    Time Delay for the Crank Termination    Oil Step    Overspeed    
720 RPM     723 Hz     723 HZ +9 sec     2295 Hz     3458 Hz    
750 RPM     723 Hz     723 HZ +9 sec     2391 Hz     3602 Hz    
900 RPM     723 Hz     723 HZ +9 sec     2869 Hz     4322 Hz    
930 RPM     723 Hz     723 HZ +9 sec     2964 Hz     4466 Hz    
1000 RPM     723 Hz     723 HZ +9 sec     3188 Hz     4803 Hz    
1050 RPM     723 Hz     723 HZ +9 sec     3347 Hz     5043 Hz    
Output Terminal of the Tachometer     14     12     11     9    
Output of the Relay     "ECTR"     "ECTTDR"     "EOSTR"     "EOSSR"    Note: Once the output of the crank termination is activated, the output will stay on until the frequency of the signal generator is set to 10 Hz and two seconds pass.Note: The output of the oil step activates after a 9 second delay after the frequency is set above the setpoint. The oil step will deactivate when the frequency falls below the setpoint.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
308E2CR Mini Hydraulic Excavator CE800001-UP (MACHINE) POWERED BY C3.3B Engine


Parts linkage Caterpillar catalog:

2901790 LINKAGE AR-BUCKET
320D, 323D L, 323D LN, 324D L, 325D L, 330D L, 336D L, 345C L, M325D L MH, M325D MH
2789293 LINKAGE GP-BUCKET
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 313D2, 314D CR, 314D LCR, 314E CR, 314E LCR, 320E L, 320E LN, 324E L, 324E LN, 329E L, 329E LN
2354043 LINKAGE GP-FELLING HEAD
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
3325077 LINKAGE GP-BUCKET
320D, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
2839018 LINKAGE AR-BUCKET
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D2, 314D CR, 314D LCR
5Y1520 LINKAGE GP-IMPLEMENT
D6D, D6D SR, D6E, D6E SR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.