5102274 LINKAGE GP-BUCKET Caterpillar parts
Rating:
Alternative (cross code) number:
CA5102274
510-2274
5102274
CA5102274
510-2274
5102274
Information:
1. Disconnect line (1) at adapter (3).2. Remove four bolts (2), adapter (3) and the gasket. 3. Disconnect two lines (5) and line (6) from the transfer pump.4. Remove two bolts (4), transfer pump (7) and the gasket.Install Fuel Transfer Pump (Later Engine)
Photos shown are of a D348 Marine Engine. Do Steps 1 and 3 only for the industrial engine. 1. Put gasket (2) and fuel transfer pump (1) in position. Install the bolts that hold the pump in place. 2. Connect line (4) to the bottom of the transfer pump.3. Connect lines (3) to the transfer pump. 4. Put the gasket in place and install adapter (5) and the bolts that hold the adapter to the regulator housing.5. Connect line (6) to the top of the adapter.Disassemble Fuel Transfer Pump (Later Engine)
start by: a) remove fuel transfer pump (later engine) 1. Remove bolts (1) and cover (2) from the pump.
Be careful not to damage the contact surfaces of the cover and pump body.
2. Remove retaining ring (3) from the shaft. 3. Remove gear (4) and gear and shaft assembly (5) from the pump body.4. Remove cage (6) from the pump body. 5. Use tool (A) to remove bearing (7) and the two seals from the cage. Remove O-ring seals (8) from the cage.6. Remove bearing (9) from the pump body. Assemble Fuel Transfer Pump (Later Engine)
1. Clean all parts thoroughly before assembly. 2. Use tooling (B) to install bearing (1) in the pump body. Install the bearing so it does not extend above the inside surface of the pump body. 3. Use tooling (A) to install the bearing in cage (2) so the end that has a taper will be toward the seals.4. Use tooling (B) to install the seals in the cage with the lips in the position shown. Install the O-ring seals on the cage. Put clean oil on the lips of the seals, the bearing and the O-ring seals. 5. Install cage (2) in the pump body as shown.6. Install gear (4) and gear and shaft assembly (3) in the pump body.7. Put a thin layer of No. 3 Permatex on the face of the pump body.
Do not let the Permatex get in the pump.
8. Put cover (5) in position on the pump body and install the bolts that hold it in place. The pump shaft must turn freely after the cover is installed.end by: a) install fuel transfer pump (later)
Photos shown are of a D348 Marine Engine. Do Steps 1 and 3 only for the industrial engine. 1. Put gasket (2) and fuel transfer pump (1) in position. Install the bolts that hold the pump in place. 2. Connect line (4) to the bottom of the transfer pump.3. Connect lines (3) to the transfer pump. 4. Put the gasket in place and install adapter (5) and the bolts that hold the adapter to the regulator housing.5. Connect line (6) to the top of the adapter.Disassemble Fuel Transfer Pump (Later Engine)
start by: a) remove fuel transfer pump (later engine) 1. Remove bolts (1) and cover (2) from the pump.
Be careful not to damage the contact surfaces of the cover and pump body.
2. Remove retaining ring (3) from the shaft. 3. Remove gear (4) and gear and shaft assembly (5) from the pump body.4. Remove cage (6) from the pump body. 5. Use tool (A) to remove bearing (7) and the two seals from the cage. Remove O-ring seals (8) from the cage.6. Remove bearing (9) from the pump body. Assemble Fuel Transfer Pump (Later Engine)
1. Clean all parts thoroughly before assembly. 2. Use tooling (B) to install bearing (1) in the pump body. Install the bearing so it does not extend above the inside surface of the pump body. 3. Use tooling (A) to install the bearing in cage (2) so the end that has a taper will be toward the seals.4. Use tooling (B) to install the seals in the cage with the lips in the position shown. Install the O-ring seals on the cage. Put clean oil on the lips of the seals, the bearing and the O-ring seals. 5. Install cage (2) in the pump body as shown.6. Install gear (4) and gear and shaft assembly (3) in the pump body.7. Put a thin layer of No. 3 Permatex on the face of the pump body.
Do not let the Permatex get in the pump.
8. Put cover (5) in position on the pump body and install the bolts that hold it in place. The pump shaft must turn freely after the cover is installed.end by: a) install fuel transfer pump (later)
Caterpillar SIS machinery equipment:
Caterpillar SIS
352F XE VG Excavator XAJ00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator YBN00001-UP (MACHINE) POWERED BY C9.3B Engine »
510-2274
LINKAGE GP-BUCKET
336 GC Excavator EBJ00001-UP (MACHINE) POWERED BY C7.1 Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator JHD00001-UP (MACHINE) POWERED BY C9.3B Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator GDY00001-UP (MACHINE) POWERED BY C9.3 Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator DKS00001-UP (MACHINE) POWERED BY C9.3B Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator SP900001-UP (MACHINE) POWERED BY C9.3 Engine »
510-2274
LINKAGE GP-BUCKET
340 Excavator TYH00001-UP (MACHINE) POWERED BY C9.3B Engine »
510-2274
LINKAGE GP-BUCKET
336 Excavator FEL00001-UP (MACHINE) POWERED BY C9.3B Engine »
510-2274
LINKAGE GP-BUCKET
349 Excavator LKG00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
352 Excavator MGR00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
349 Excavator RBY00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
349F & 349F L Excavators BZ200001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
352F Excavators A9J00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
349F L Excavator KEA00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
336F L XE & 336F LN XE Excavators DFY00001-UP (MACHINE) POWERED BY C9.3 Engine »
510-2274
LINKAGE GP-BUCKET
349F LXE Excavators RAX00001-UP (MACHINE) POWERED BY C13 Engine »
510-2274
LINKAGE GP-BUCKET
Caterpillar parts catalog:
Parts linkage Caterpillar catalog:
5087675
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
4973961
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
4973959
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
3938032
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5060538
LINKAGE AR-BUCKET
Caterpillar
Caterpillar
4893937
LINKAGE AS
Caterpillar
Caterpillar
5218031
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5218028
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5218024
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5218023
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5218022
LINKAGE GP-BUCKET
Caterpillar
Caterpillar
5102282
LINKAGE GP-BUCKET
Caterpillar
Caterpillar