AVSPARE.COM
parts catalog

LOCK GP-SWING 0876264 - Caterpillar



0876264 LOCK GP-SWING Caterpillar parts 375 LOCK
Rating:
13
Alternative (cross code) number:
CA0876264
087-6264
0876264
Caterpillar 0876264 LOCK GP-SWING

Buy LOCK GP-SWING 0876264 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 0876264:

EXCAVATOR  375   Caterpillar
  For full view, you need register

Information:


Install a blocking plate at location (S) on either winch.
Install a 0 to 28000 kPa (0 to 4000 psi) pressure gauge at pressure tap (G) .
Start the engine and run the engine at high idle.
Fully shift the control lever to HIGH SPEED RAISE for the winch that has the blocking plate. The reading on the gauge is the setting of the main relief valve.
Do not hold relief pressure for more than 10 seconds. If more time is required to check the setting, wait for one minute before you develop the relief pressure again.
If the pressure reading in Step 4 was not 18250 + 520 - 175 kPa (2650 + 75 - 25 psi), add or remove shims (5) from the main relief valve. See Table 11.
Illustration 18 g00543888
Main Relief Valve (5) Shims
Table 11
Change in Pressure in the Main Relief Valve by Removing One Shim or Adding One Shim    
Shim
Part Number    Thickness    Approximate Change    
5J-2721    
0.13 mm (.005 inch)    
180 kPa (26 psi)    
5J-2722    
1.22 mm (.048 inch)    
1730 kPa (251 psi)    
Illustration 19 g00539403
Control lever positions for the hook and the boom (A) Quick drop (B) Power down (C) Modulated lower (D) Neutral (E) Slow raise (F) Fast raise (X) Hook winch (Y) Boom winchBoom Relief Valve and Hook Relief Valve (POWER DOWN)
Install blocking plates at location (R) on both winches.
Install a 0 to 28000 kPa (0 to 4000 psi) pressure gauge at pressure tap (G) .
Start the engine and run the engine at high idle.
Fully shift the boom control lever to POWER DOWN. The high reading on the pressure gauge is the setting for the boom relief valve (POWER DOWN).
Fully shift the hook control lever to POWER DOWN. The high reading on the pressure gauge is the setting for the hook relief valve (POWER DOWN).
Illustration 20 g00543901
POWER DOWN relief valve (1) Cap (2) Adjustment screw (3) Locknut
If the pressure readings from Steps 4 and 5 were not 10500 520 kPa (1520 75 psi), perform the following adjustment:
Stop the engine.
Remove cap (1) and loosen locknut (3) .
Turn adjustment screw (2) clockwise in order to increase the pressure. Turn the screw counterclockwise in order to decrease the pressure.
Hold the adjustment screw in order to prevent movement while you tighten the locknut. Install cap (1) .
Check the pressure setting on the relief valve again. If necessary, readjust the setting again until the proper setting is attained.Counterweight Relief Valve
Illustration 21 g00543940
Implement Hydraulic Pump (H) Pressure tap for the small section of the pump (counterweight circuit)
Install a 0 to 28000 kPa (0 to 4000 psi) pressure gauge on a 6V-3081 Hose Assembly .
Install the hose with the pressure gauge onto pressure tap (H) .
Start the engine and run the engine at high idle.
Do not hold the control lever in the RETRACT position at relief pressure for more than five seconds.
Move the counterweight control lever to the RETRACT position. The high reading on the pressure gauge is the setting of the counterweight relief valve. The

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
375, 375L TRACK-TYPE EXCAVATORS 6RL00001-UP (MACHINE) POWERED BY 3406 ENGINE


Parts lock Caterpillar catalog:

2A4429 LOCK-RETAINER
1140, 1160, 120, 120B, 120G, 120H, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 143H, 14E, 14G, 14H, 14H NA, 14M, ...
0856445 LOCK
305.5, 305.5E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314...
0856446 LOCK
305.5, 305.5E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314...
8T2888 LOCK GP
120G, 12G, 130G, 140G, 14G, 160G, 16G, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 308C, 308D, 375, 375 L, 385B, 385C, 385C FS, 385C L, 38...
7I1703 LOCK AS
311, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 365B, 375
1507429 LOCK AS
325C, 345B, 345B II, 345B II MH, 345B L, 350, 365B, 365B II, 375, 375 L, 5080, W345B II
7N0243 LOCK-ROD BOLT
1673C, 16G, 3176, 3208, 3304, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412E, 3512, 3512B, 3512C, 3516C, 5130, 5230, 613C, 627B, 627E, 631D, 631E, 631G, 633D, 633E II, 637D, 637E, 6...
1560235 LOCK
120H, 120H ES, 120H NA, 135H, 135H NA, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B L, 325C, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 570, 574,...
1W2715 LOCK-RETAINER
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 205B, 214B, 224B, ...
5Q4018 LOCK GP
330B L, 330C L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.