AVSPARE.COM
parts catalog

LOCKNUT 0000003 - Caterpillar



0000003 LOCKNUT Caterpillar parts D6M, E120 LOCKNUT
Rating:
73
Alternative (cross code) number:
CA0000003
000-0003
0000003
Caterpillar 0000003 LOCKNUT

Buy LOCKNUT 0000003 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, TRACK-TYPE TRACTOR,

You can buy parts: .

$13.45

28 May 2018

Sylvania: Sylvania
5 x 6" 4w T5 Fluorescent Tube Cool White [4000k] (SLI 0000003)
4W T5 Halophosphor Mini Tube, Cool White, 150mm || halophosphate coating to give a standard performance || B class energy efficiency rating || average life of 5,000 hours || all items expertly packaged with care

11 Jan 2018

Sylvania: Sylvania
30 x 6" 4w T5 Fluorescent Tube Cool White [4000k] (SLI 0000003)
4W T5 Halophosphor Mini Tube, Cool White, 150mm||halophosphate coating to give a standard performance||B class energy efficiency rating||average life of 5,000 hours||all items expertly packaged with care
$8.94

28 May 2018

Sylvania: Sylvania
2 x 6" 4w T5 Fluorescent Tube Cool White [4000k] (SLI 0000003)
4W T5 Halophosphor Mini Tube, Cool White, 150mm || halophosphate coating to give a standard performance || B class energy efficiency rating || average life of 5,000 hours || all items expertly packaged with care
Number on catalog scheme: None
  
  For full view, you need register

Compatible equipment models: 0000003:

EXCAVATOR  E120  
TRACK-TYPE TRACTOR  D6M   Caterpillar

Information:


Illustration 1 g02623458
Schematic for the Pilot Pressure Solenoid ValveThis solenoid is connected to the Implement ECM. The Implement ECM sends the diagnostic information to the Machine ECM via the CAN data link. This diagnostic code is recorded when the Implement ECM detects an incomplete electrical path. The electrical path from the Implement ECM to the solenoid back to the Implement ECM is incomplete.The possible causes for this diagnostic code are listed:
The signal circuit from the Implement ECM to the solenoids is open.
The return circuit from the solenoid is open.
The internal windings for the solenoid have high impedance.
The internal windings for the solenoid are open.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the solenoid with the diagnostic code from the harness.
Observe the ON/OFF status of the diagnostic code indicator.
At the harness connector for the solenoid, place a jumper wire between contact 1 (wire E918-GN) and contact 2 (wire H708-OR).Expected Result:The diagnostic code remains active.Results:
YES - The diagnostic code remains active. The harness has failed or the Implement ECM has failed. Proceed to Test Step 2.
NO - The diagnostic code is inactive.Repair: The solenoid valve has failed. Repeat this test in order to verify the failure. Repair the solenoid or replace the solenoid. Repair the connecting harness or replace the connecting harness at the solenoid.STOPTest Step 2. CHECK THE HARNESS.
Turn the disconnect switch to the OFF position.
Remove the jumper wire from contact 1to 2.
Reconnect the solenoid valve to the harness.
Disconnect the harness from the Implement ECM.
At the harness connector for the Implement ECM, measure the resistance between contact 4 (wire H708-OR) and contact 2 (wire E918-GN).Expected Result:The resistance is greater than 5000 Ohms (no continuity).Results:
YES - The resistance is greater than 5000 Ohms (no continuity).Repair: The harness circuit has failed. Wire H708-OR is open in the harness between the Implement ECM and the solenoid valve, or the wire E918-GN to the solenoid valve is open. Repair the harness or replace the harness.STOP
NO - The resistance is less than 5000 Ohms.Repair: Check the circuit again.If the cause of the problem is not found, contact the Technical Communicator for your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the Implement ECM requires replacement, see Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP

Caterpillar parts catalog:

Caterpillar parts catalog
E120 HYDRAULIC EXCAVATOR 1LF00001-UP (MACHINE) POWERED BY 6D14 ENGINE
D6M TRACK-TYPE TRACTOR CUSTOM PARTS MANUAL-POWER SHIFT, LOW 2RN00001-UP (MACHINE)


Parts locknut Caterpillar catalog:

1K8872 LOCKNUT
955K, 977D, 977H, D9L
3171117 LOCKNUT
120K, 120K 2, 657E, D6T LGP, D6T LGPPAT, D7E, D7E LGP, R1600H
4J8734 LOCKNUT
641, 641B, 651, 651B, 651E, 657, 657B, 657E, 657G, 666, 973D, 988B, 988F, 988F II, 992, D10N, D10R, D10T, D10T2, D9L, R1700 II, R1700G, R2900, R2900G
3D4904 LOCKNUT
120B, 120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12M 2, 12M 3 AWD, 130G, 135H, 135H NA, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 140M 3 AWD, 143H, 1...
9C8287 LOCKNUT-STAKE
2470C, 2570C, 2670C, 2864C, 515, 518C, 525, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 936F, 938F, 938G, 938G II, 950F, 950F II, 950G, 950G II, 950H, ...
9T0389 LOCKNUT
950G II, 966H, D6R III
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.