OPERATOR STATION
PANEL GPSERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMSBASIC ENGINE
PISTON & ROD GPCYLINDER HEAD GP
SERVICE EQUIPMENT AND SUPPLIES
PROTECTION GPSHIPPING GP
OPERATOR STATION
PANEL GP
#M00649220990
444-3378: PANEL GP-CONTROL
444-3378 PANEL GP-CONTROL (CHG -00 THRU -04)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 494-0472 Y | [1] | DISPLAY GP-MONITOR | ||
| 471-8474 Y | [1] | HARNESS AS-PANEL | ||
| 506-0830 Y | [1] | STRIP GP-TERMINAL | ||
| 419-5974 | [1] | ADAPTER AS (AT04-6P TO RJ45) | ||
| 432-2668 | [1] | NUT (13/16-28-THD) | ||
| 8T-6912 M | [4] | BOLT (M8X1.25X50-MM) | ||
| 455-9583 | [1] | CONTROL GP-UNPROGRAMMED | ||
| 498-2830 | [1] | ELECTRONICS GP-MONITOR | ||
| 448-4866 | [1] | GASKET | ||
| 8T-9655 | [8] | MOUNT-ISOLATION | ||
| 390-1208 | [1] | SHROUD | ||
| 6I-1418 | [4] | SPACER (8.2X12.7X28.7-MM THK) | ||
| 390-1209 | [1] | SWITCH AS (EMERGENCY STOP) | ||
| 9N-0869 | [8] | WASHER-HARD (8.8X25.5X2-MM THK) | ||
| M | METRIC PART | |||
| R | REMANUFACTURED PART MAY BE AVAILABLE | |||
| Y | SEPARATE ILLUSTRATION | |||
#M00649220991
456-3765: PANEL GP-CONTROL
456-3765 PANEL GP-CONTROL (CHG -00 THRU -03)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7K-1181 | [9] | STRAP-CABLE | |
| 2. | 103-6272 | [1] | SEAL | |
| 3. | 203-9007 | [1] | NUT (1-1/2-18-THD) | |
| 4. | 270-2679 | [1] | LOCKWASHER | |
| 5. | 314-9101 | [5] | BRACKET-END | |
| 6. | 339-2958 | [1] | GASKET | |
| 7. | 340-7298 | [1] | CAP AS | |
| 8. | 350-3459 | [1] | MODULE | |
| 9. | 368-7965 Y | [1] | CONTROL GP-GENERATOR SET | |
| 10. | 390-1208 | [1] | SHROUD | |
| 11. | 390-1209 | [1] | SWITCH AS (EMERGENCY STOP) | |
| 12. | 420-0437 | [1] | SWITCH-PUSH | |
| 13. | 433-6752 | [1] | PANEL AS | |
| 7T-1099 | [2] | LINK | ||
| 14. | 433-6755 | [1] | PANEL AS | |
| 7T-1099 | [8] | LINK | ||
| 15. | 433-6756 | [4] | BRACKET | |
| 16. | 447-6625 | [1] | COVER-TERMINAL | |
| 17. | 448-4866 | [1] | GASKET | |
| 18. | 456-0792 | [39] | BLOCK-TERMINAL | |
| 19. | 456-3762 | [1] | MARKER AS-TERMINAL | |
| 20. | 456-3766 Y | [1] | HARNESS AS-PANEL | |
| 21. | 460-2362 | [3] | STRIP-CONTACT | |
| 22. | 460-2363 | [41] | TERMINAL | |
| 23. | 460-2366 | [1] | STRIP-CONTACT | |
| 24. | 460-2367 | [1] | COVER-END | |
| 25. | 460-6273 | [1] | FILM-IDENTIFICATION (CONTROL PANEL) | |
| 26. | 464-3976 | [2] | TERMINAL | |
| 27. | 1H-3338 | [6] | LOCKWASHER | |
| 28. | 4F-7957 | [8] | BOLT (1/4-20X0.875-IN) | |
| 29. | 5P-0537 | [16] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 30. | 6V-8225 M | [6] | NUT (M6X1-THD) | |
| 31. | 9S-8750 | [8] | NUT-FULL (1/4-20-THD) | |
| 32. | 9X-8267 | [6] | WASHER (6.6X12X2-MM THK) | |
| 33. | 496-0302 | [1] | COVER | |
| 34. | 230-0975 | [1] | PLATE-WARNING (ELECTRICAL SHOCK HAZARD) | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#M00649220992
6L-4502: CHART-PLATE & FILM
6L-4502 CHART-PLATE & FILM (CHG -0303)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 7E-7852 | [6] | FILM (PICTOGRAPH) | ||
| INSTALL THREE FILMS ON THE AIR CHOKE ACTUATOR BRACKET: ONE VISIBLE FROM THE SIDE, ONE VISIBLE FROM THE FRONT, | ||||
| AND ONE VISIBLE FROM THE TOP OF THE ENGINE. | ||||
| INSTALL TWO FILMS ON THE WASTE GATE ACTUATOR BRACKET: ONE VISIBLE FROM THE FRONT, & ONE VISIBLE FROM THE REAR | ||||
| OF THE ENGINE. | ||||
| INSTALL ONE FILM ON THE SIDE OF THE FUEL ACTUATOR BRACKET. | ||||
| 230-0974 | [6] | FILM (TRANSFORMER) | ||
| INSTALL ONE FILM ON EACH (310-3180) TRANSFORMER ASSEMBLY BETWEEN THE TOP & RH SIDE FLANGE BOLTS. | ||||
| [1] | FILM-INFORMATION (EMISSION CONTROL) | |||
| INSTALL THE FILM ON RH SIDE OF THE ENGINE IN THE CENTER OF THE 2ND VISIBLE CAM COVER FROM THE REAR. | ||||
| INSTALL CLEAR LAMINATE ON FILM. | ||||
| 7W-5890 | [1] | FILM-INFORMATION (STANDARD ROTATION) | ||
| INSTALL ON TOP OF FLYWHEEL HOUSING. | ||||
| 4P-6469 | [6] | FILM-NOTICE (SPARK PLUG) | ||
| INSTALL ONE FILM CENTERED ON THE OUTBOARD FACE OF EACH VALVE COVER VISIBLE FROM THE SIDE. | ||||
| 224-9828 | [1] | FILM-WARNING (SHOCK HAZARD) | ||
| INSTALL FILM ON THE FACE OF THE CONTROL BOX IN THE BOTTOM LH CORNER OF THE BOX. | ||||
| 228-3581 | [1] | FILM-WARNING (DO NOT OPERATE, READ OMM) | ||
| INSTALL FILM ON THE FACE OF THE CONTROL BOX IN THE BOTTOM RH CORNER OF THE BOX. | ||||
| 233-6084 | [2] | FILM-WARNING (FIRE, STOP ENGINE, DO NOT OPEN) | ||
| INSTALL ONE FILM ON EACH SIDE OF THE ENGINE, ON THE RH SIDE CENTERED ON THE FIRST VISIBLE CRANKCASE COVER FROM THE REAR | ||||
| AND LH SIDE CENTERED ON THE FIRST VISIBLE CRANKCASE COVER FROM THE FRONT. | ||||
| 115-5852 | [1] | PLATE & FILM GP (ENGINE INFORMATION) | ||
| CONTACT YOUR LOCAL DEALER. | ||||
| INSTALL FILM BETWEEN THE LAST TWO CRANKCASE COVERS ON THE RH REAR OF THE CYLINDER BLOCK. | ||||
| INSTALL CLEAR LAMINATE OVER FILM. | ||||
| 298-5631 | [2] | PLATE-IDENTIFICATION (CAT) | ||
| INSTALL ONE PLATE ON EACH SIDE OF THE ENGINE, ON THE FIRST VISIBLE CAM COVER FROM THE RH REAR & THE FIRST VISIBLE | ||||
| CAM COVER FROM LH FRONT. | ||||
| 230-0975 | [1] | PLATE-WARNING (ELECTRICAL SHOCK HAZARD) | ||
| INSTALL FILM ON THE FRONT FACE OF THE BOX GROUP IN THE LOWER LH CORNER. | ||||
| 3N-3790 | [1] | PLATE-SERIAL NUMBER (ENGINE) | ||
| CONTACT YOUR LOCAL DEALER. | ||||
| REFLATTEN AFTER STAMPING. | ||||
| INSTALL ON LH SIDE OF CYLINDER BLOCK BETWEEN REAR TWO CRANKCASE COVERS USINB 7B-3028 DRIVE SCREWS. | ||||
| STAMP SERIAL NUMBER IN BLOCK JUST BELOW PLATE IN FIGURES 6 HIGH. | ||||
| 7B-3028 | [2] | SCREW-DRIVE (NO 4X 3/16-IN) | ||
#M00649220993
4C-9043: COMPRESSOR GP-PISTON RING
4C-9043 COMPRESSOR GP-PISTON RING (CHG -00)
PART OF 9U-5107 TOOL GP-SPARK IGNITED ENGINE
PART OF 9U-5107 TOOL GP-SPARK IGNITED ENGINE
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS#M00649220994
8T-2660: COMPRESSOR GP-VALVE SPRING
8T-2660 COMPRESSOR GP-VALVE SPRING (CHG -00 THRU -02)
VALVE SPRING-MANUAL
VALVE SPRING-MANUAL
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 8T-2661 | [1] | ADAPTER-SPRING COMPRESSOR | ||
| 2A-4781 | [1] | BOLT (1/4-20X2.75-IN) | ||
| 8F-6350 | [1] | BOLT (3/8-16X8-IN) | ||
| 8T-2663 | [1] | HANDLE-EXTENSION | ||
| 8T-2664 | [1] | LEVER GP | ||
| 1B-2714 | [1] | BOLT (1/4-20X2.5-IN) | ||
| 1B-4427 | [1] | NUT-JAM (1/4-20-THD) | ||
| 9S-8752 | [1] | NUT-FULL (3/8-16-THD) | ||
| 6H-3956 | [1] | PIN |
#M00649220995
443-8082: COVER GP-PROTECTION
443-8082 COVER GP-PROTECTION (CHG -00)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 374-2273 | [48] | PROTECTOR-STUD |
#M00649220996
449-8962: COVER GP-PROTECTION
449-8962 COVER GP-PROTECTION (CHG -00)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 374-2273 | [24] | PROTECTOR-STUD |
#M00649220997
503-5953: COVER GP-PROTECTION
503-5953 COVER GP-PROTECTION (CHG -00)
FOR USE WITH LH SERVICE
FOR USE WITH LH SERVICE
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3R-6789 | [1] | CAP-FLARED (1-5/16-12-THD) |
#M00649220998
418-9887: COVER GP-SHIPPING
418-9887 COVER GP-SHIPPING (CHG -01 THRU -03)
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SIS#M00649220999
467-2144: COVER GP-SHIPPING
467-2144 COVER GP-SHIPPING -REGULATOR HOUSING (CHG -00)
FOR USE WITH G3616 PETROLEUM, 4835 BHP @ 1000 RPM, G3606B PETROLEUM, 1875 BHP @ 1000 RPM, G3612B PETROLEUM, 3750 BHP @ 1000 RPM, G3608B PETROLEUM, 2500 BHP @ 1000 RPM
FOR USE WITH G3616 PETROLEUM, 4835 BHP @ 1000 RPM, G3606B PETROLEUM, 1875 BHP @ 1000 RPM, G3612B PETROLEUM, 3750 BHP @ 1000 RPM, G3608B PETROLEUM, 2500 BHP @ 1000 RPM
For full view, you need register
Parts for your G3608 GAS ENGINE:
CATERPILLAR SISInformation:
OPERATOR STATION
PANEL GP
Engine News
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
Operation and Maintenance Manual
Special Instruction
Installation of the Petroleum Human Machine Interface Display {4490, 7451}
Installation of the Petroleum Human Machine Interface Display {4490, 7451}
Installation of the Petroleum Human Machine Interface Display {4490, 7451}
Systems Operation
Testing and Adjusting
Troubleshooting
