450-2564 KIT-GASKET -SINGLE FUEL INJECTOR S/N SSE1-UP; SYE1-UP KIT CONTAINS THE SEALS NEEDED TO REINSTALL ONE INJECTOR INTO THE CYLINDER HEAD FOR USE WITH @@@@@373-3754@@@@@ 966M XE

450-2564 KIT-GASKET -SINGLE FUEL INJECTOR
S/N SSE1-UP; SYE1-UP
KIT CONTAINS THE SEALS NEEDED TO REINSTALL ONE INJECTOR INTO THE CYLINDER HEAD
FOR USE WITH @@@@@373-3754@@@@@

i05598412 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
263-4016	[1]	SEAL
326-2041	[1]	SEAL
326-2042	[1]	SEAL

		FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT

		HTTP://DEALER.CAT.COM/RELATED

#M00656141771

471-9655: KIT-GASKET

KIT-GASKET

471-9655 KIT-GASKET
S/N B8P1-UP
KIT CONTAINS GASKETS, SEALS, AND BENDABLE LOCKS TO REINSTALL THE OIL PAN, INTERNAL OIL PUMP, AND BLOCK COVERS
FOR USE WITH @@@@@373-3754@@@@@

i06237899 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
195-0452	[1]	GASKET
280-4322	[1]	GASKET
190-6114	[1]	GASKET-OIL PAN
180-3907	[1]	SEAL-INTEGRAL (TRANSMISSION COOLER)
5P-7530	[1]	SEAL-O-RING
6V-3250	[2]	SEAL-O-RING
6V-5064	[2]	SEAL-O-RING
6V-6609	[2]	SEAL-O-RING
8T-5917	[2]	SEAL-O-RING
330-8197	[1]	SEAL-O-RING
137-8101	[2]	SEAL-O-RING
210-9246	[1]	SEAL-O-RING
214-7566	[3]	SEAL-O-RING
214-7568	[7]	SEAL-O-RING
228-7089	[5]	SEAL-O-RING
238-5080	[3]	SEAL-O-RING
238-5081	[2]	SEAL-O-RING

		FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT

		HTTP://DEALER.CAT.COM/RELATED

#M00656141772

471-9660: KIT-GASKET

KIT-GASKET

471-9660 KIT-GASKET -OIL COOLER, LINES
S/N B8P1-UP
KIT CONTAINS THE GASKETS AND SEALS TO ASSEMBLE AND REINSTALL THE OIL COOLERS, OIL FILTER BASE. AND ATTACHING LINES
FOR USE WITH @@@@@373-3754@@@@@

i06502877 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
209-7290	[1]	GASKET
209-7293	[1]	GASKET
180-3907	[1]	SEAL-INTEGRAL
214-7568	[1]	SEAL-O-RING
464-0509	[1]	SEAL-O-RING
8T-5917	[1]	SEAL-O-RING
219-7000	[1]	SEAL-O-RING
305-4484	[3]	SEAL-O-RING
214-7566	[2]	SEAL-O-RING
228-7089	[1]	SEAL-O-RING
238-5080	[1]	SEAL-O-RING
238-5081	[3]	SEAL-O-RING
238-5082	[1]	SEAL-O-RING

		FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT

		HTTP://DEALER.CAT.COM/RELATED

#M00656141773

471-9663: KIT-GASKET

KIT-GASKET

471-9663 KIT-GASKET -SINGLE CYLINDER HEAD
S/N B8P1-UP
KIT CONTAINS THE GASKETS, SEALS AND BENDABLE LOCKS TO REBUILD AND REINSTALL A CYLINDER HEAD. KIT INCLUDES THE TURBO GASKETS, BUT DOES NOT INCLUDE THE FUEL INJECTOR SEALS. ORDER A SINGLE INJECTOR SEAL KIT AS NEEDED.. FOR IN-LINE 4 AND 6 CYLINDER ENGINES WITH ONE CYLINDER HEAD. THEFOLLOWING TURBPMOUNTING HARDWARE WILL BE INCLUDED: BOLTS, NUTS, STUDS, WASHERS, SPACERS ETC.. APPLIES TO SINGLE CYLINDER HEAD KIT PART NUMBERS 317-8750 - UP

i06541838 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
161-3411	[6]	GASKET
197-8418	[1]	GASKET
197-8419	[1]	GASKET (TURBOCHARGER)
349-9657	[1]	GASKET
262-1940	[1]	GASKET AS-CYLINDER HEAD
375-2467 M	[4]	LOCKNUT-FLANGE (M10X1.5-THD)
256-2209	[1]	SEAL
4G-4972	[1]	SEAL-O-RING
6V-3251	[2]	SEAL-O-RING
6V-3831	[1]	SEAL-O-RING
6V-6609	[2]	SEAL-O-RING
6V-8001	[1]	SEAL-O-RING
7F-8268	[2]	SEAL-O-RING
8T-5917	[1]	SEAL-O-RING
238-5081	[1]	SEAL-O-RING
033-6033	[1]	SEAL-O-RING
124-1858	[1]	SEAL-O-RING
160-0526	[1]	SEAL-O-RING
214-7566	[5]	SEAL-O-RING
214-7567	[1]	SEAL-O-RING
214-7568	[7]	SEAL-O-RING
228-7090	[1]	SEAL-O-RING
228-7091	[1]	SEAL-O-RING
228-7100	[1]	SEAL-O-RING
228-7101	[2]	SEAL-O-RING
238-5078	[6]	SEAL-O-RING
238-5080	[2]	SEAL-O-RING
305-4484	[4]	SEAL-O-RING
310-7258	[6]	SEAL-O-RING
310-7259	[6]	SEAL-O-RING
341-0979	[2]	SEAL-O-RING
260-0113	[1]	SEAL-VALVE COVER
245-9750 M	[4]	STUD-TAPERLOCK (M10X1.5X50-MM)

		FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT

		HTTP://DEALER.CAT.COM/RELATED
M		METRIC PART

#M00656141774

360-0218: LINES GP-DIAGNOSTIC

LINES GP-DIAGNOSTIC

360-0218 LINES GP-DIAGNOSTIC
S/N B8P1-UP
PART OF 386-0945, 506-4553 CONFIGURATION AR

i05756273 M0065614

3600218 LINES GP-DIAGNOSTIC Parts scheme

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8T-4195 M	[2]	BOLT (M10X1.5X30-MM)
2.	6V-0852	[4]	CAP-DUST
3.	169-5863	[3]	ADAPTER AS
			(EACH INCLUDES)
	4J-5477	[1]	SEAL-O-RING
	7X-7945	[1]	ADAPTER (9/16-18-THD)
4.	192-5017	[1]	BRACKET AS
5.	197-4566	[1]	BRACKET AS
6.	204-2281	[6]	STRAP-CABLE
7.	204-8000	[6]	MOUNTING-CABLE TIE
8.	260-9187	[1]	CONNECTOR AS
	6V-8397	[1]	SEAL-O-RING
	8T-9358	[1]	CONNECTOR
9.	148-8433	[1]	TEE AS
	6V-8397	[2]	SEAL-O-RING
	6V-9836	[1]	TEE-SWIVEL
10.	148-8351	[3]	ELBOW AS
			(EACH INCLUDES)
	4J-5477	[1]	SEAL-O-RING
	6V-9849	[1]	ELBOW
11.	8T-4136 M	[8]	BOLT (M10X1.5X25-MM)
12.	433-6025	[1]	BRACKET AS
13.	417-3340	[1]	HOSE AS
14.	417-3341	[1]	HOSE AS
15.	417-3342	[1]	HOSE AS
16.	417-3344 I	[1]	HOSE AS
17.	187-2120	[1]	ELBOW AS
	4J-5477	[1]	SEAL-O-RING
	8C-8408	[1]	ELBOW
18.	164-5567	[4]	COUPLER AS-QUICK DISCONNECT (MALE)
	6V-3965	[1]	FITTING (QUICK DISCONNECT)
	214-7568	[1]	SEAL-O-RING
19.	2P-1279	[3]	LOCKNUT (9/16-18-THD)
20.	344-5675 M	[2]	NUT (M10X1.5-THD)
21.	4D-7388	[1]	CLIP (LOOP)
22.	4S-1962	[1]	CLIP (LOOP)
23.	6V-9168	[1]	NUT (11/16-16-THD)
24.	8T-4121	[6]	WASHER-HARD (11X21X2.5-MM THK)
	I		REFER TO HYDRAULIC INFORMATION SYSTEM
	M		METRIC PART

#M00656141775

359-3149: PLATE & FILM GP

PLATE & FILM GP

359-3149 PLATE & FILM GP
S/N SSE1-UP; SYE1-UP
PART OF 373-3750 ENGINE AR

i05043593 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	J	[1]	PLATE-SERIAL NUMBER (ENGINE)
2.	430-5251	[3]	FILM-WARNING (HIGH PRESSURE, READ OMM)
3.	293-9659	[2]	FILM-WARNING (UNIVERSAL, READ OMM)
4.	295-8454	[2]	FILM-WARNING (ACID BURN HAZARD, READ OMM)
5.	350-0684	[1]	FILM-INFORMATION (ENGINE OIL, READ OMM)
6.	419-8867	[1]	PLATE-IDENTIFICATION (CAT)
	J		CONTACT YOUR LOCAL DEALER

#M00656141776

371-7057: PLATE & FILM GP

PLATE & FILM GP

371-7057 PLATE & FILM GP
S/N B8P1-UP
PART OF 370-2082 CONFIGURATION AR

i06902226 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
443-1946 Y	[1]	FILM GP
		S/N B8P1-202
454-0202 Y	[1]	FILM GP
		S/N B8P203-UP
1P-2807	[2]	FILM-IDENTIFICATION (LIFT EYE LOCATION)
		(ONE EACH AT FRONT LIFT EYES)
7X-3229	[2]	FILM-IDENTIFICATION (LIFT EYE, TIE-DOWN LOCATION)
		(ONE EACH AT REAR LIFT & TIE-DOWN EYES)
7X-7644	[2]	FILM-IDENTIFICATION (TIE-DOWN)
		(ONE EACH AT FRONT TIE-DOWN EYES)
353-7106	[1]	FILM-IDENTIFICATION (GREASE POINTS)
		(ON FRONT COVER OF HYDRAULIC SERVICE CENTER NEXT TO GREASE FITTINGS ON NEEF)
455-1084	[1]	FILM-IDENTIFICATION (CAT)
		(ON INSIDE OF ELECTRICAL DISCONNECT DOOR, CENTERED VERTICALLY & 15-MM AWAY FROM DOOR LATCH)
423-4101	[1]	FILM-IDENTIFICATION (BATTERY DISCONNECT, READ OMM)
		(ABOVE DEF PURGE LIGHT IN DISCONNECT SWITCH COMPARTMENT)
444-8663	[1]	FILM-IDENTIFICATION (GREASE POINTS, READ OMM)
		(ON RIGHT HAND NEEF NEAR GREASE FITTINGS)
446-8426	[1]	FILM-IDENTIFICATION (DIAGNOSTIC PORTS)
		(ON INSIDE OF HYDRAULIC SERVICE CENTER DOOR NEAR DIAGNOSTIC TEST FITTINGS)
438-5944	[1]	FILM-IDENTIFICATION (GREASE PRESSURE PORTS)
		(ON INSIDE OF LEFT HAND NEEF PLATE NEXT TO DIFFERENTIAL LOCK MANIFOLD)
480-5098	[2]	FILM-INFORMATION (BELT ROUTING)
		1-(ON TOP OF LEFT SIDE ENGINE END FRAME RAIL, TOP EDGE OF FILM TOWARDS FRONT OF MACHINE; CENTERED FORE-AFT TO LIFT TIE DOWN, CENTERED ON FRAME RAIL)
		1-(ON COMPRESSOR GUARD FACING OUTBOARD OF MACHINE WITH TOP OF FILM 28-MM BELOW CENTER OF UPPER SLOT ON GUARD; RIGHT SURFACE 10-MM FROM BEND ON COMPRESSOR GUARD)
146-6747	[2]	FILM-INFORMATION (24-VOLT)
		1-(OUTSIDE OF BATTERY BOX COVER BELOW LH CORNER OF FILM-WARNING ON LEFT SIDE OF MACHINE)
		1-(INSIDE DISCONNECT SWITCH COMPARTMENT NEAR JUMP START RECEPTACLE)
449-9226	[1]	FILM-INFORMATION (CAT SATO)
		(ON FRONT FACE OF BATTERY BOX ABOVE TRANSMISSION OIL FILL)
6V-2679	[1]	FILM-INSTRUCTION (WIPER)
		S/N B8P203-300
		(ON OUTSIDE OF RIGHT SIDE PLATFORM ON VERTICAL SURFACE NEAR WASHER BOTTLE)
124-2456	[2]	FILM-INSTRUCTION (NO STEP)
		(ON TOP OF HOOD BEHIND CAB ON EACH SIDE)
437-8530	[2]	FILM-INSTRUCTION (LUBRICATION POINTS)
		S/N B8P1-202
		(ON BOTH SIDES OF HYDRAULIC SERVICE CENTER DOOR)
486-3156	[2]	FILM-INSTRUCTION (LUBRICATION POINTS)
		S/N B8P203-300
		(ON BOTH SIDES OF HYDRAULIC SERVICE CENTER DOOR)
563-3330	[2]	FILM-IDENTIFICATION (LUBRICATION POINTS)
		S/N B8P301-UP
		1-(ON INSIDE OF HYDRAULIC SERVICE CENTER DOOR 10-MM DOWN FROM TOP, 123-MM AWAY FROM HINGED EDGE OF DOOR)
		1-(ON OUTSIDE OF HYDRAULIC SERVICE CENTER DOOR, CENTERED BETWEEN TOP RUNGS)
430-8957	[1]	FILM-INFORMATION (ENGINE OIL, READ OMM)
		(ON FAN MOTOR SUPPORT ASSEMBLY ON LOWER HORIZONTAL SUPPORT BAR 10-MM FROM EDGE)
A	[1]	PLATE-SERIAL NUMBER (ENGINE)
		(LEFT SIDE ON REAR CYLINDER BLOCK)
239-6986	[1]	PLATE-SERIAL NUMBER (MACHINE)
		(ON LEFT SIDE OF NEEF. FRONT EDGE OF PLATE 95-MM TO THE REAR OF CENTER LINE OF LIFT CYLINDER PIN. TOP OF PLATE 30-MM ABOVE HORIZONTAL CENTER LINE OF LIFT CYLINDER PIN. FOR CONCEALED PIN LOCATION SEE CHART)
9R-1499	[2]	REFLECTOR (RED)
		(CENTERED IN THE RECESSES ON COUNTERWEIGHT)
506-3501	[1]	FILM-GAUGE IDENTIFICATION (DIESEL EXHAUST FLUID)
		S/N B8P301-UP
		(CENTERED HORIZONTALLY ON VERTICAL SURFACE OF DEF FILL SUPPORT BRACKET & 10-MM BELOW BEND IN DEF FILL SUPPORT BRACKET)
A		NOT PART OF THIS GROUP
Y		SEPARATE ILLUSTRATION

#M00656141777

372-0525: PLATE & FILM GP

PLATE & FILM GP

372-0525 PLATE & FILM GP
S/N B8P1-UP
PART OF 372-2085, 372-2094, 509-4097 CONVERSION AR-MACHINE

i06759003 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
349-8603	[1]	FILM-INSTRUCTION (FUEL, READ OMM)
		(ON LH HOOD PANEL BELOW DOOR OPENING REARWARD OF HOT SURFACE FILM)
224-8945	[1]	FILM-WARNING (DO NOT USE ETHER, U.S.)
		(ON TOP OF HOOD PANEL 385-MM PLUS/MINUS 25-MM FROM FRONT EDGE, CENTERED WITH AIR CLEANER & OFFSET TO MACHINE LEFT SIDE BY 100-MM PLUS/MINUS 25-MM)
224-7830	[1]	FILM-WARNING (HIGH PRESSURE, READ OMM, U.S.)
		(ON RH OUTER FACE OF NON ENGINE FRAME, TOP EDGE 5 MM BELOW BOTTOM EDGE OF FILM-WARNING & LH EDGE ALIGNED WITH LH EDGE OF FILM-WARNING)
225-0313	[2]	FILM-WARNING (JUMP START, READ OMM, U.S.)
		1-(ON LEFT SIDE OF MACHINE ON OUTSIDE OF BATTERY BOX COVER)
		1-(INSIDE DISCONNECT SWITCH COMPARTMENT ABOVE SWITCHES)
226-1242	[2]	FILM-WARNING (CRUSH HAZARD, STAY BACK, U.S.)
		(ON BOTH OUTER SIDE FACES OF NON ENGINE FRAME, BOTTOM EDGE 100-MM ABOVE BOTTOM OF SIDE PLATE & REAR EDGE 15-MM FORWARD TO REAR EDGE OF PLATE ASSEMBLY)
226-1275	[1]	FILM-WARNING (CRUSH HAZARD, READ OMM, U.S.)
		(ON LEFT OUTER FACE OF NON ENGINE FRAME, BOTTOM EDGE 15-MM ABOVE BOTTOM OF SIDE PLATE & RIGHT EDGE 15-MM FORWARD OF RIGHT EDGE OF PLATE ASSEMBLY)
228-9105	[2]	FILM-WARNING (HOT SURFACE-VERTICAL)
		1-(ON FLAT SURFACE ON FRONT OF AIR CLEANER COVER AS FAR REARWARD AS POSSIBLE)
		1-(ON LH SIDE OF RADIATOR STRUCTURE)
451-1364	[2]	FILM-WARNING (FAN)
		S/N A8P1-957; KJP1-7103
463-0969	[2]	FILM-WARNING (ROTATING FAN)
		S/N A8P958-UP; B8P1-UP; KJP7104-UP; M5S1-UP
		(ON BOTH SIDES OF RADIATOR STRUCTURE)
444-5638	[1]	FILM-WARNING (LEAK DETECTION, READ OMM)
		(ON INSIDE SURFACE ON BOTH SIDES OF NEEF ALIGN REAR EDGE WITH REAR EDGE OF CUTOUT IN NEEF VALVE SHELF, BOTTOM EDGE 300-MM UP FROM VALVE SHELF SURFACE)
228-7315	[2]	FILM-WARNING (HOT SURFACE, HANDS CLEAR)
		S/N B8P1-UP; M5S1-UP
		(BELOW SERVICE DOOR ON BOTH SIDES OF HOOD)

#M00656141778

444-6482: PLATE & FILM GP

PLATE & FILM GP

444-6482 PLATE & FILM GP -BIODEGRADABLE OIL
S/N B8P1-UP

i05425357 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
	139-6810	[1]	FILM-IDENTIFICATION (BIODEGRADABLE OIL)
			(FILM ON TOP OF HYDRAULIC TANK, BETWEEN FILLER NECK & INSIDE OF TANK, ORIENT TO BE READ FROM TRACTOR LH SIDE)

#M00656141779

525-2019: PLATE & FILM GP

PLATE & FILM GP

525-2019 PLATE & FILM GP
S/N B8P1-UP
PART OF 372-2096, 386-0923 CONVERSION AR-MACHINE

i06952479 M0065614

For full view, you need register

Parts for your 966M XE WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
524-3641	[1]	FILM-INFORMATION (AIR CONDITIONER)
		(ON BLANK REGION OF PLATE-INST(A/C). SELECT LANGUAGE LABEL MATCHING LITERATURE LANGUAGE SPECIFIED ON MACHINE ORDER)
524-3642	[1]	PLATE-INSTRUCTION (AIR CONDITIONER)
		(NEXT TO COMPRESSOR CHARGING PORT)
347-5687	[1]	PLATE-INSTRUCTION (AIR CONDITIONER, READ OMM)
		(NEXT TO COMPRESSOR CHARGING PORT)
3S-2093	[1]	STRAP-CABLE
		(NEXT TO COMPRESSOR CHARGING PORT)

Information:

SERVICE EQUIPMENT AND SUPPLIES

GASKET & SEAL KITS

Special Instruction

Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}
Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}

Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555}
O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555}

Lip Type Seals {0599, 0733, 5050, 7555}
Lip Type Seals {0599, 0733, 5050, 7555}

Reuse And Salvage Guidelines

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Disassembly and Assembly

Duo-Cone Conventional Seals - Install
966M Tier 4 Series XE and 972M Tier 4 Series XE Wheel Loader Power Train

Caterpillar Parts SIS Catalog 966M XE :

543-2137 KIT-FLUIDS SERVICE

501-0595 KIT-FILM

478-7468 FILM-INFORMATION

484-9693 FILM GP-U.S.

484-9694 FILM GP-INTERNATIONAL

360-0218 LINES GP-DIAGNOSTIC

359-3149 PLATE & FILM GP

371-7057 PLATE & FILM GP

372-0525 PLATE & FILM GP

444-6482 PLATE & FILM GP