1224197 MANIFOLD-EXHAUST Caterpillar parts
3306C
Rating:
Alternative (cross code) number:
CA1224197
122-4197
1224197
CA1224197
122-4197
1224197
Weight: 12 pounds 5 kg.
TRUCK ENGINE,
Compatible equipment models: 1224197:
Number on catalog scheme:
2
For full view, you need register
Information:
Remove Pistons
preparatory steps: a) remove cylinder head assemblyb) remove oil pump1. Remove the carbon ridge from the top inside surface of cylinder liners.2. Rotate the crankshaft until two pistons are at bottom dead center. 3. Remove the connecting rod caps (1) from these pistons, and push the pistons upward until the rings clear the cylinder liner. 4. Remove the two pistons.5. Repeat Step 2 through 4 for the remaining pistons.Install Pistons
1. Thoroughly lubricate the crankshaft bearing journals and cylinder liners with clean SAE 30 engine oil.2. Lubricate the piston rings and connecting rod bearings with clean SAE 30 engine oil. 3. Using compressor (A), install the pistons with "V" mark on piston aligned with "V" mark on cylinder block. Guide the lower end of the rod over the crankshaft journal to prevent damage to the crankshaft.4. Lubricate the threads of cap retaining bolts with clean SAE 30 engine oil.5. Position the caps on the connecting rods, and install retaining nuts. Tighten nuts initially to 30 3 lb. ft. (4,1 0,4 mkg). Mark the nut and end of bolt, and tighten nut an additional 90° from mark.
When installing connecting rod cap, be sure that the number marked on side of cap is adjacent to and corresponds to the number marked on side of connecting rod.
6. Rotate the crankshaft until the next two bearing journals are at bottom dead center.7. Repeat Steps 2 through 5 for the remaining two pistons.concluding steps: a) install oil pumpb) install cylinder head assemblyDisassemble Pistons
preparatory step: a) remove pistons 1. Remove piston pin retaining rings (2).2. Remove piston pin (1) and remove piston from the connecting rod. 3. Remove the piston rings using ring expander (A).Assemble Pistons
1. Using ring expander (A), install the piston rings. The two compression rings are marked "UP - 1" and "UP - 2". The rings must be installed with these marks toward the top of the piston with "UP - 1" being the top ring. After all three rings have been installed on piston, stagger the ring caps 120° apart.2. Lubricate the piston pin with clean SAE 30 engine oil. 3. Position the piston on the connecting rod with the "V" mark (2) on the piston and number (1) on the connecting rod on the same side.4. Install the piston pin retaining rings. Make certain the retaining rings are seated in their grooves.concluding step: a) install pistons
preparatory steps: a) remove cylinder head assemblyb) remove oil pump1. Remove the carbon ridge from the top inside surface of cylinder liners.2. Rotate the crankshaft until two pistons are at bottom dead center. 3. Remove the connecting rod caps (1) from these pistons, and push the pistons upward until the rings clear the cylinder liner. 4. Remove the two pistons.5. Repeat Step 2 through 4 for the remaining pistons.Install Pistons
1. Thoroughly lubricate the crankshaft bearing journals and cylinder liners with clean SAE 30 engine oil.2. Lubricate the piston rings and connecting rod bearings with clean SAE 30 engine oil. 3. Using compressor (A), install the pistons with "V" mark on piston aligned with "V" mark on cylinder block. Guide the lower end of the rod over the crankshaft journal to prevent damage to the crankshaft.4. Lubricate the threads of cap retaining bolts with clean SAE 30 engine oil.5. Position the caps on the connecting rods, and install retaining nuts. Tighten nuts initially to 30 3 lb. ft. (4,1 0,4 mkg). Mark the nut and end of bolt, and tighten nut an additional 90° from mark.
When installing connecting rod cap, be sure that the number marked on side of cap is adjacent to and corresponds to the number marked on side of connecting rod.
6. Rotate the crankshaft until the next two bearing journals are at bottom dead center.7. Repeat Steps 2 through 5 for the remaining two pistons.concluding steps: a) install oil pumpb) install cylinder head assemblyDisassemble Pistons
preparatory step: a) remove pistons 1. Remove piston pin retaining rings (2).2. Remove piston pin (1) and remove piston from the connecting rod. 3. Remove the piston rings using ring expander (A).Assemble Pistons
1. Using ring expander (A), install the piston rings. The two compression rings are marked "UP - 1" and "UP - 2". The rings must be installed with these marks toward the top of the piston with "UP - 1" being the top ring. After all three rings have been installed on piston, stagger the ring caps 120° apart.2. Lubricate the piston pin with clean SAE 30 engine oil. 3. Position the piston on the connecting rod with the "V" mark (2) on the piston and number (1) on the connecting rod on the same side.4. Install the piston pin retaining rings. Make certain the retaining rings are seated in their grooves.concluding step: a) install pistons
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
9L5805
MANIFOLD GP-EXHAUST
1673C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 350, 627B, D250B, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D35C, D6C, E300, E300B
1673C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 350, 627B, D250B, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D35C, D6C, E300, E300B
9Y0805
MANIFOLD GP-EXHAUST
3306, 3306C
3306, 3306C
1673C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 350, 621R, 627B, D250B, D250E, D250E II, D25C, D300B, D300E, D300E II, D30C, D350C, D35C, D6C, E300B
1673C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 350, 621R, 627B, D250B, D250E, D250E II, D25C, D300B, D300E, D300E II, D30C, D350C, D35C, D6C, E300B
1673C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 350, 621R, 627B, D250B, D250E, D250E II, D25C, D300B, D300E, D300E II, D30C, D350C, D35C, D6C, E300B
14G, 14H NA, 16G, 16H NA, 3176, 3176B, 3204, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3508, 3508B, 3512, 3512B, 3516, 3516B, 611, 615C, 621E, 621F, 623E, 623F, 627E, 627F, 814B, 815B, 826C, 916, 926, 9...
3306, 3306C
3306, 3306C
24M, 3406B, 3406C, 3406E, 824C, 824H, 825H, 826H, 980G, 980H, C-15, C-16, PM-200, PM-201, RM-500
3406B, 3406C, 3406E, C-15, C-16, C16
3406B, 3406C, 3406E, AD45B, AD55, C-15, C-16, C16
140H, 143H, 14H, 160H, 163H, 3176B, 3176C, 3196
3406B, 3406E
1007400
MANIFOLD-EXHAUST
3406B
3406B
1168059
MANIFOLD-FUEL
G3306
G3306
3116, 3126