1910561 MANIFOLD GP-EXHAUST Caterpillar parts
303.5
Rating:
Alternative (cross code) number:
CA1910561
191-0561
1910561
CA1910561
191-0561
1910561
MINI HYD EXCAVATOR,
Compatible equipment models: 1910561:
Information:
Tests Of Settings For Relief Valves
Move the machine to a location where the blade can be lowered and will sit level on the ground (floor). Get the hydraulic oil to operating temperature. Turn off the engine. Move the control lever for the dozer to each operation position several times to take the pressure out of the lines.Dozer Circuit
1. Clean the oil and dirt off of connections and fittings.2. Install a 9S8093 or 5H4020 Blocking Plate Assembly (1) in the rod end line for each of the dozer cylinders. Install it as close to the cylinder as possible.3. Install a 0 to 4000 psi (0 to 27 500 kPa) pressure gauge in pressure tap (2).4. Start the engine and run it at high idle speed to get full flow from the pump.
BLOCKING PLATE ASSEMBLY
1. Blocking plate assembly.
PRESSURE TAP LOCATION
2. Pressure tap.5. Move the blade control to RAISE and LOWER positions to get maximum system pressure. Do not keep the system at relief pressure for more than ten seconds. If more time is needed, wait one minute and do Step 5 again.6. Inspect all lines, connections and fittings for leaks.7. Relief valve pressure must be as shown in Relief Valve Setting Chart.8. Turn off the engine and move the blade control lever to all positions several times to release pressures.9. Remove the Blocking Plate Assemblies and connect lines to cylinders.10. Check the oil level in the hydraulic tank and add oil if necessary. Make reference to the respective machine's LUBRICATION & MAINTENANCE GUIDE. If the machine is equipped with a ripper, the main relief valve setting can be checked by using the procedure for the ripper circuit.Tilt And Tilt Pilot Circuits
1. Clean the oil and dirt off of connections and fittings.2. Install a 0 to 4000 psi (0 to 27 500 kPa) pressure gauge in pressure tap (3).
PRESSURE TAP LOCATION
3. Pressure tap.3. Start the engine and run it at high idle to get full flow from the pump.4. Move the blade control to RAISE position until blade is clear of the ground.5. Move the tilt control lever to TILT LEFT and TILT RIGHT to get maximum system pressure. Do not keep the system at relief pressure for more than ten seconds. If more time is needed, wait one minute and do Step 5 again.6. Inspect all
Move the machine to a location where the blade can be lowered and will sit level on the ground (floor). Get the hydraulic oil to operating temperature. Turn off the engine. Move the control lever for the dozer to each operation position several times to take the pressure out of the lines.Dozer Circuit
1. Clean the oil and dirt off of connections and fittings.2. Install a 9S8093 or 5H4020 Blocking Plate Assembly (1) in the rod end line for each of the dozer cylinders. Install it as close to the cylinder as possible.3. Install a 0 to 4000 psi (0 to 27 500 kPa) pressure gauge in pressure tap (2).4. Start the engine and run it at high idle speed to get full flow from the pump.
BLOCKING PLATE ASSEMBLY
1. Blocking plate assembly.
PRESSURE TAP LOCATION
2. Pressure tap.5. Move the blade control to RAISE and LOWER positions to get maximum system pressure. Do not keep the system at relief pressure for more than ten seconds. If more time is needed, wait one minute and do Step 5 again.6. Inspect all lines, connections and fittings for leaks.7. Relief valve pressure must be as shown in Relief Valve Setting Chart.8. Turn off the engine and move the blade control lever to all positions several times to release pressures.9. Remove the Blocking Plate Assemblies and connect lines to cylinders.10. Check the oil level in the hydraulic tank and add oil if necessary. Make reference to the respective machine's LUBRICATION & MAINTENANCE GUIDE. If the machine is equipped with a ripper, the main relief valve setting can be checked by using the procedure for the ripper circuit.Tilt And Tilt Pilot Circuits
1. Clean the oil and dirt off of connections and fittings.2. Install a 0 to 4000 psi (0 to 27 500 kPa) pressure gauge in pressure tap (3).
PRESSURE TAP LOCATION
3. Pressure tap.3. Start the engine and run it at high idle to get full flow from the pump.4. Move the blade control to RAISE position until blade is clear of the ground.5. Move the tilt control lever to TILT LEFT and TILT RIGHT to get maximum system pressure. Do not keep the system at relief pressure for more than ten seconds. If more time is needed, wait one minute and do Step 5 again.6. Inspect all
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
1445986
MANIFOLD GP-CONTROL
301.5, 302.5, 303.5, 304.5
301.5, 302.5, 303.5, 304.5
1618280
MANIFOLD-EXHAUST
3013, 3013C, 302.5, 303.5, C1.5
3013, 3013C, 302.5, 303.5, C1.5
1537770
MANIFOLD
302.5, 303.5, 304, 304.5, 305, 305.5, 305.5E, 306, 306E
302.5, 303.5, 304, 304.5, 305, 305.5, 305.5E, 306, 306E
1910576
MANIFOLD-INLET
303.5
303.5
1639726
MANIFOLD
303.5, 304.5
303.5, 304.5
2244500
MANIFOLD GP-CONTROL
SG16, SG16B
SG16, SG16B
3251356
MANIFOLD GP-INLET
3024, 3024C, C2.2
3024, 3024C, C2.2
2020524
MANIFOLD GP-INLET
3014, 3024
3014, 3024