1922043 MANIFOLD Caterpillar parts
3176C, 3196, C-10, C-12
Rating:
Alternative (cross code) number:
CA1922043
192-2043
1922043
CA1922043
192-2043
1922043
INDUSTRIAL ENGINE,
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket As 2
B - Forcing Screw (20 mm X 100 mm) 2
C - Loctite C5A Anti-Seize -
D - Loctite 5188 -
E - Loctite 243 - Start By:
Remove the swing motor.
Thoroughly clean the area around the swing drive prior to removal.
Put identification marks on the swing drive to mark the location for installation purposes.
Illustration 1 g00694361
Remove bolts (1).
Illustration 2 g00694371
Attach Tooling (A) and a suitable lifting device to swing drive (2). The weight of swing drive (2) is approximately 190 kg (420 lb).
Remove corks (3) from the threaded holes in the swing drive housing.
Illustration 3 g06093597
Install Tooling (B) in each threaded hole in swing drive (2).Note: Slowly tighten one forcing screw for no more than two turns, and then tighten the other forcing screw for no more than two turns. At the same time keep tension on the swing drive with the suitable lifting device. Tighten the forcing screws evenly in this manner to remove the swing drive.
Use Tooling (B) to remove swing drive (2).Installation Procedure
Install swing drive (2) in the reverse order of removal.
Apply Tooling (C) to the locating pin and the locating pin bore.
Apply Tooling (D) to the mating surface of swing drive (2) and the main frame.
Apply Tooling (E) to bolts (1).
Tighten bolts (1) to a torque of 900 100 N m (664 74 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket As 2
B - Forcing Screw (20 mm X 100 mm) 2
C - Loctite C5A Anti-Seize -
D - Loctite 5188 -
E - Loctite 243 - Start By:
Remove the swing motor.
Thoroughly clean the area around the swing drive prior to removal.
Put identification marks on the swing drive to mark the location for installation purposes.
Illustration 1 g00694361
Remove bolts (1).
Illustration 2 g00694371
Attach Tooling (A) and a suitable lifting device to swing drive (2). The weight of swing drive (2) is approximately 190 kg (420 lb).
Remove corks (3) from the threaded holes in the swing drive housing.
Illustration 3 g06093597
Install Tooling (B) in each threaded hole in swing drive (2).Note: Slowly tighten one forcing screw for no more than two turns, and then tighten the other forcing screw for no more than two turns. At the same time keep tension on the swing drive with the suitable lifting device. Tighten the forcing screws evenly in this manner to remove the swing drive.
Use Tooling (B) to remove swing drive (2).Installation Procedure
Install swing drive (2) in the reverse order of removal.
Apply Tooling (C) to the locating pin and the locating pin bore.
Apply Tooling (D) to the mating surface of swing drive (2) and the main frame.
Apply Tooling (E) to bolts (1).
Tighten bolts (1) to a torque of 900 100 N m (664 74 lb ft).
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
C-15, C-16, C15, C18, CX31-C15I, CX35-P800, TH35-C15I
C-9, C9, TH31-E61
3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, AP-1055D, AP-755, BG-...
3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, AP-1055D, AP-755, BG-...
3126, 3126B, 3126E, 325C, 325C FM, AP-1055D, BG-2455D, BG-260D, C7
3126, 3126B, 3126E
2239798
MANIFOLD-INLET
C-10, C-12
C-10, C-12
2250127
MANIFOLD-INLET
C-10, C-12
C-10, C-12
2223890
MANIFOLD
C-15
C-15
2037778
MANIFOLD-EXHAUST
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, 973D, C-9, TK711, TK721, TK722, TK732, TK741, TK751, TK752
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, 973D, C-9, TK711, TK721, TK722, TK732, TK741, TK751, TK752
1949644
MANIFOLD-EXHAUST
627G, 627H, 627K LRC, 637D, 637E, 637G, 814F II, 815F II, 816F II, C-9, C9, CX31-C9I, TH31-E61
627G, 627H, 627K LRC, 637D, 637E, 637G, 814F II, 815F II, 816F II, C-9, C9, CX31-C9I, TH31-E61