2106565 MANIFOLD GP-EXHAUST Caterpillar parts
3054
Rating:
Alternative (cross code) number:
CA2106565
210-6565
2106565
CA2106565
210-6565
2106565
GENERATOR SET,
Compatible equipment models: 2106565:
Number on catalog scheme:
For full view, you need register
Information:
Use snap ring pliers to remove snap ring (26) from sun gear (27) .
Illustration 23 g00527629
Remove sun gear (27) from planetary carrier (25) .
Illustration 24 g00527656
Use snap ring pliers to remove snap ring (28) that secures planetary gear (29) to spindle (30) .
Use Tooling (E) to remove planetary gear (29) from spindle (30) .
Repeat Steps 32 and 33 for the other four planetary gears.
Illustration 25 g00527840
Illustration 26 g00528079
Remove bolt (31), tab (32) and ball (33) from spindle nut (34). Note: Use the access hole in ring gear (35) to access bolt (31). Ring gear (35) can be rotated in order to align the access hole with bolt (31) .
Illustration 27 g00530820
Note: The procedure for drilling will create a small amount of steel chips. Do not allow the chips to fall into bearing kit (35) .
Use a 4.76 mm (.188 inch) drill bit (41) to remove the damaged portion of threads which was caused by ball (33). This will require drilling into spindle (30) to a depth of approximately 1.5 mm (.06 inch).
Clear the steel chips from the hole. Do not allow the chips to fall into bearing kit (35) .
Repeat Steps 35 through 37 in order to remove the remaining bolt assembly.
Illustration 28 g00527917
Install the reaction shaft from Tooling (F) on spindle (30), as shown.
Illustration 29 g00527930
Install the socket from Tooling (F) over spindle nut (34), as shown.
Use Tooling (F) to remove spindle nut (34). The torque that is required to remove the spindle nut is approximately 1500 N m (1100 lb ft).
Illustration 30 g00528669
Remove bearing kit (35) from spindle (30) .Note: It may be necessary to remove bearing kit (35) by pulling bearing kit (35) with ring gear (36) .
Illustration 31 g00528772
Remove ring gear (36) from spindle (30) .
Illustration 32 g00528781
Remove one half of Duo-cone seal kit (37) from ring gear (36) .
Illustration 33 g00528793
Remove bearing kit (38) from ring gear (36) .
Illustration 34 g00528800
Remove the second half of Duo-cone seal kit (37) from spindle (30) .
Illustration 35 g00528814
Typical example
Use Tooling (G) to shape spindle threads (39), if the threads appear damaged.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
1317705
MANIFOLD-INLET
3054, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, TH103, TH62, TH63, TH82, TH83
3054, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, TH103, TH62, TH63, TH82, TH83
2107562
MANIFOLD
3054
3054
2223779
MANIFOLD GP-CONTROL
BH150, CVP16, VVP25
BH150, CVP16, VVP25
2072309
MANIFOLD GP-CONTROL
CVP16, VVP25
CVP16, VVP25
2059395
MANIFOLD GP-CONTROL
CVP16, VVP25
CVP16, VVP25
2175479
MANIFOLD GP-INLET
318C, 319C
318C, 319C
2175594
MANIFOLD GP-EXHAUST
318C, 319C
318C, 319C
2788514
MANIFOLD GP-EXHAUST
R2900G
R2900G
2690996
MANIFOLD GP-EXHAUST
R2900G, R3000H
R2900G, R3000H
24H, 24M, 824C, 824G, 824G II, 825G, 825G II, 826C, 826G, 826G II, 834B, 836, 980C, 980F, 980F II, 980G, 980G II, 988B, AD30, D350E, D350E II, D400, D400E, D44B, D550B, R2900, R2900G, R3000H
2374291
MANIFOLD GP-EXHAUST
AD30, C15, C18, CX31-C15I, CX35-P800, TH35-C15I
AD30, C15, C18, CX31-C15I, CX35-P800, TH35-C15I
2361787
MANIFOLD GP-EXHAUST
AD45B, AD55
AD45B, AD55
2232529
MANIFOLD & MTG GP-STEERING
438D, 442D
438D, 442D