2596744 MANIFOLD GP-CONTROL Caterpillar parts
422E, 428E
Rating:
Alternative (cross code) number:
CA2596744
259-6744
2596744
CA2596744
259-6744
2596744
Weight: 15 pounds 7 kg.
BACKHOE LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2024-04-19
2022-07-11
Number on catalog scheme:
2
For full view, you need register
Information:
Type 1 Fuel Filters
Illustration 1 g02791865
Typical example
Loosen the vent screw (1) on the secondary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent screw (1) to a torque of 20 N m (15 lb ft)
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for
Illustration 1 g02791865
Typical example
Loosen the vent screw (1) on the secondary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent screw (1) to a torque of 20 N m (15 lb ft)
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for
Caterpillar SIS machinery equipment:
Caterpillar SIS
422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POWERED BY 3054C Engine »
259-6744
MANIFOLD GP-CONTROL
428E Backhoe Loader Parallel Lift SNL00001-UP (MACHINE) POWERED BY 3054C Engine »
259-6744
MANIFOLD GP-CONTROL
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine »
259-6744
MANIFOLD GP-CONTROL
428E Backhoe Loader DXC00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine »
259-6744
MANIFOLD GP-CONTROL
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
2458780
MANIFOLD GP-RIDE CONTROL
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, 904H, 906H, 906H2, 907H, 907H2, 908H, 908H2, 910K, 914K
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, 904H, 906H, 906H2, 907H, 907H2, 908H, 908H2, 910K, 914K
2596745
MANIFOLD GP-CONTROL
414E, 416E, 422E
414E, 416E, 422E
2375408
MANIFOLD GP-EXHAUST
3054C, 414E, 416D, 416E, 422E, 422F, 424D, AP-300
3054C, 414E, 416D, 416E, 422E, 422F, 424D, AP-300
3715674
MANIFOLD-EXHAUST
3054C, 414E, 416D, 416E, 422E, 422F, 424D, AP-300, C4.4
3054C, 414E, 416D, 416E, 422E, 422F, 424D, AP-300, C4.4
3715700
MANIFOLD-EXHAUST
3054C, 3054E, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, AP-300D, C4.4
3054C, 3054E, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, AP-300D, C4.4
1226060
MANIFOLD GP-INLET
35, 45, 55
35, 45, 55
3N1678
MANIFOLD GP
D379, D379A, D379B
D379, D379A, D379B
2072675
MANIFOLD & MTG GP-EJECTOR
740, 740B
740, 740B
1215731
MANIFOLD GP-EXHAUST
5130B, 776D, 777, 777B, 777C, 777D, D11N, D11R
5130B, 776D, 777, 777B, 777C, 777D, D11N, D11R
2950647
MANIFOLD GP-EXHAUST
854K, 992K
854K, 992K
2L0196
MANIFOLD CARBURETOR AND BREATHER GROUP
D326F, D337F
D326F, D337F
3988029
MANIFOLD GP-EXHAUST
3512C, XQC1200
3512C, XQC1200
3080421
MANIFOLD GP-RETURN
216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 247B, 247B3, 252B, 252B3, 257B, 257B3, 259B3, 268B
216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 247B, 247B3, 252B, 252B3, 257B, 257B3, 259B3, 268B
3361453
MANIFOLD GP-EXHAUST
D6T LGP, D6T XL, D7E, D7E LGP
D6T LGP, D6T XL, D7E, D7E LGP
2350783
MANIFOLD GP-CONTROL
M313C, M315C, M316C, M318C, M318C MH, M322C
M313C, M315C, M316C, M318C, M318C MH, M322C