3722558 MANIFOLD GP-EXHAUST Caterpillar parts
R1600H, R1700G
Rating:
Alternative (cross code) number:
CA3722558
372-2558
3722558
CA3722558
372-2558
3722558
LOAD HAUL DUMP,
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7M-7260 Liquid Gasket 1
B - 3/8 - 16 NC Guide Bolts 4
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00604494
Typical Example
Inspect O-ring seal (4) for the connector to the oil pump. If the seal is cut, scratched, or cracked, obtain a new seal for assembly. Lubricate the bore for the seal with clean engine oil. Install the seal.
Make sure that the surface for gasket (3) is clean. Apply Tooling (A) to gasket (3) . Install Tooling (B) in the oil pan. Place the gasket into position.
Improper lift rigging can allow unit to tumble causing injury and damage.
Note: If improper equipment is used to lift the engine, injury and damage can occur. Use cables or chains that are properly rated for the weight. Use a spreader bar and attach the cables or chains according to the information that is on the lifting film for the engine.
Illustration 2 g00604420
Typical Example
Attach a suitable lifting device to the engine lifting eyes.
The weight of the 3508 Engine is approximately 4445 kg (9800 lb). The weight of the oil pan is approximately 240 kg (530 lb).
The weight of the 3512 Engine is approximately 5900 kg (13,000 lb). The weight of the oil pan is approximately 295 kg (650 lb).
The weight of the 3516 Engine is approximately 7711 kg (17,000 lb). The weight of the oil pan is approximately 409 kg (900 lb).
Lift the engine. Place the engine onto the oil pan or place the oil pan in position under the engine. Remove Tooling (B) from the oil pan.
Illustration 3 g00604419
Typical Example
Illustration 4 g00604418
Typical Example
Install bolts (2) that hold the engine and the oil pan together.
Illustration 5 g00604417
Typical Example
Install bolts (1) that hold the connector for the oil pump to the oil pan.
Fill the engine crankcase with oil. Refer to the Operation and Maintenance Manual, "Capacities (Refill)" for the oil capacity.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7M-7260 Liquid Gasket 1
B - 3/8 - 16 NC Guide Bolts 4
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00604494
Typical Example
Inspect O-ring seal (4) for the connector to the oil pump. If the seal is cut, scratched, or cracked, obtain a new seal for assembly. Lubricate the bore for the seal with clean engine oil. Install the seal.
Make sure that the surface for gasket (3) is clean. Apply Tooling (A) to gasket (3) . Install Tooling (B) in the oil pan. Place the gasket into position.
Improper lift rigging can allow unit to tumble causing injury and damage.
Note: If improper equipment is used to lift the engine, injury and damage can occur. Use cables or chains that are properly rated for the weight. Use a spreader bar and attach the cables or chains according to the information that is on the lifting film for the engine.
Illustration 2 g00604420
Typical Example
Attach a suitable lifting device to the engine lifting eyes.
The weight of the 3508 Engine is approximately 4445 kg (9800 lb). The weight of the oil pan is approximately 240 kg (530 lb).
The weight of the 3512 Engine is approximately 5900 kg (13,000 lb). The weight of the oil pan is approximately 295 kg (650 lb).
The weight of the 3516 Engine is approximately 7711 kg (17,000 lb). The weight of the oil pan is approximately 409 kg (900 lb).
Lift the engine. Place the engine onto the oil pan or place the oil pan in position under the engine. Remove Tooling (B) from the oil pan.
Illustration 3 g00604419
Typical Example
Illustration 4 g00604418
Typical Example
Install bolts (2) that hold the engine and the oil pan together.
Illustration 5 g00604417
Typical Example
Install bolts (1) that hold the connector for the oil pump to the oil pan.
Fill the engine crankcase with oil. Refer to the Operation and Maintenance Manual, "Capacities (Refill)" for the oil capacity.
Caterpillar SIS machinery equipment:
Caterpillar SIS
C11 Engine Emissions Retrofit Repower Tier II for R1600G Load Haul Dump Truck 9YZ00001-UP (MACHINE) »
372-2558
MANIFOLD GP-EXHAUST
R1700G Load Haul Dump SBR00001-UP (MACHINE) POWERED BY C11 Engine »
372-2558
MANIFOLD GP-EXHAUST
R1600H Load Haul Dump 9SD00001-UP (MACHINE) POWERED BY C11 Engine »
372-2558
MANIFOLD GP-EXHAUST
R1700G Load Haul Dump XBR00001-UP (MACHINE) POWERED BY C11 Engine »
372-2558
MANIFOLD GP-EXHAUST
C11 Engine Emissions Repower Upgrade Tier II for R1600G Load Haul Dump 9PP00001-UP (MACHINE) »
372-2558
MANIFOLD GP-EXHAUST
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...
611, 615, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, D250B, D250E, D250E II, D25C, D25D, D300B, D300E, D300E II, R1600, R1600G, R1600H, R1700 II, R1700G
3162777
MANIFOLD AS
R1700G
R1700G
1869445
MANIFOLD AS
R1600, R1600G, R1600H, R1700G
R1600, R1600G, R1600H, R1700G
2555123
MANIFOLD
R1700G
R1700G
2914047
MANIFOLD
R1600G, R1600H, R1700G
R1600G, R1600H, R1700G
1869426
MANIFOLD
R1600, R1600G, R1600H, R1700G
R1600, R1600G, R1600H, R1700G
2884484
MANIFOLD-HYDRAULIC
R1700G
R1700G
2184656
MANIFOLD
R1600, R1600G, R1700G
R1600, R1600G, R1700G
1869608
MANIFOLD AS
R1600, R1600G, R1600H
R1600, R1600G, R1600H
1869789
MANIFOLD AS
R1600, R1600G, R1600H
R1600, R1600G, R1600H
2261380
MANIFOLD
R1600, R1600G, R1600H
R1600, R1600G, R1600H
2919301
MANIFOLD GP-EXHAUST
R1700G
R1700G
2872519
MANIFOLD GP-EXHAUST
R1700G
R1700G
3963251
MANIFOLD GP-EXHAUST
R2900G, R3000H
R2900G, R3000H
R2900G
3462640
MANIFOLD GP-EXHAUST
R2900G
R2900G
2788514
MANIFOLD GP-EXHAUST
R2900G
R2900G
2694277
MANIFOLD GP-EXHAUST
3024C, C2.2
3024C, C2.2
2688808
MANIFOLD GP-EXHAUST
3024C, C2.2
3024C, C2.2
1992119
MANIFOLD GP-EXHAUST
302.5C, 303
302.5C, 303
2911663
MANIFOLD GP-INLET
R1700G
R1700G