MANIFOLD 4F7038 - Caterpillar

4F7038 MANIFOLD Caterpillar parts 977D

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4F7038
4F-7038
4F7038

Weight: 30 pounds 13 kg.

Buy MANIFOLD 4F7038 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

17 Jul 2017
34.00[15.30] pounds
CTP: CTP

Caterpillar MANIFOLD (4F7038)
4F7038 Caterpillar Weight(lbs): 34.00 Length(cm): 95.3000 Width(cm): 17.8000 Depth(cm): 8.9000

$210.11

17 Jul 2017

CTP: CTP

4F7038 Manifold Fits Caterpillar
4F7038 Manifold

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#77417 4F7038

2017-07-17

Number on catalog scheme: None

Caterpillar 4F7038 Parts scheme MANIFOLD

For full view, you need register

Compatible equipment models: 4F7038:

TRACK LOADER 977D Caterpillar

Information:

D8, D9 Tractors;
583, 594 Pipelayers;
D353, D379, D398, D399 Industrial And Marine EnginesSUPPLEMENT: 08/31/81SERVICE MAGAZINE, JUNE 29, 1981, PAGE 12.In the article "New Inlet And Exhaust Valves And Valve Guides Have Tighter Fit To Prevent Corrosion And Guide Wear," the diameter of the stem for the new valve is wrong. Change the first sentence in the second paragraph to: "The new valves have smaller, 9.441 mm (.3717") diameter stems."
Also, add "*50V5990" under "First Used", across from "D8" in Chart A.
--------------- END SUPPLEMENT ---------------Reference: Put a mark through the March 16, 1981, SERVICE MAGAZINE article, "New Inlet And Exhaust Valves And Valve Guides Have Tighter Fit To Prevent Corrosion And Guide Wear," on Page 4, and make reference to this article. This article has the information given in the earlier article, and it has some new information that has become available.Description of Change: New inlet and exhaust valves and valve guides are used in the above products. The new valves have smaller, 9.441 mm (.3717") diameter stems. The new valve guides have thread-like grooves inside their bores.
Used together, the new valves and valve guides have a tighter fit than the former valves and guides. The tighter fit keeps combustion gases out of the area between the valves and valve guides.
Formerly, a valve with a 12.7 mm (.500") diameter stem was used. It was possible for combustion gases to get in between the valves and guides. These gases caused corrosion which then caused the guides to wear rapidly. The rate of corrosion and wear is increased when high sulfur fuel is used.
Adaptable To: The new parts are in effect with the Serial Numbers given in Chart A under "First Used." The new parts, used together, are adaptable to all products given in Chart A under "Adaptable To". Chart B has the parts for installation in D9 Tractors, 594 Pipelayers, and D353, D379, D398 and D399 Industrial and Marine Engines. Chart C has the parts for installation in D8 Tractors and 583 Pipelayers. Chart D has the service head assemblies which are available with the new valves and guides.
The guides must have 0.038 mm (.0015") clearance. Some guides will have to be machined; other guides will not. For clearance checks, the valve stem is to be measured about 115 mm (4.50") from the keeper end.
The clearance between the valve and valve guide has an effect on the service life of the valve guide. It is necessary to have the correct clearance to stop the movement of combustion gases and the corrosion and wear which are the results.
Use the 1P7451 Valve Guide Honing Group and 5P8615 Honing Oil to get the final clearance, if necessary. The complete procedure for use of the 1P7451 Valve Guide Honing Group is given in Special Instruction, Form No. SMHS7526.
Use the 1P7430 Valve Guide Driver Assembly and the 2P2313 Valve Guide Driver Bushing to install the valve guides to the correct depth in heads for D9 Tractors, 594 Pipelayers, and D353, D379, D398 and D399 Industrial and Marine