4P7322 MANIFOLD GP-EXHAUST Caterpillar parts
G3512
Rating:
Alternative (cross code) number:
CA4P7322
4P-7322
4P7322
CA4P7322
4P-7322
4P7322
Weight: 20 pounds 9 kg.
GAS ENGINE,
Compatible equipment models: 4P7322:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7505     Mobile Transmission Jack (Low Lift)     1    
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Illustration 1 g00809285
Use Tooling (A) and support the bottom guard that will be installed. The weight of the bottom guards is approximately 45 kg (100 lb) to 84 kg (185 lb).
Illustration 2 g00809287
Install pin (6), nuts (4), and the washers that attach bottom guard (3) to both sides of machine frame (5) .
Move Tooling (A) and support the next bottom guard, as needed. Repeat Step 1 to Step 2 and install the bottom guards with pivot pin assembly.
Illustration 3 g00701916
Use Tooling (A) and a suitable block to install the front bottom guard.
Install bolts (2) and the washers. Install nuts (1) and the washers.Raising Bottom Guards
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-9200     Lever Puller     1    
Illustration 4 g00809277
Attach suitable lifting device (1) to one side of the machine. Attach Tooling (A) to the other side of the machine. Attach suitable lifting device (1) to Tooling (A) and pull tightly under bottom guard (2), as shown.
Illustration 5 g01205500
Use Tooling (A) to raise the bottom guard from ground level. The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids and debris. The bottom guard pivots on pin (5) .
Illustration 6 g00809278
Install nuts (3) on both sides that secure bottom guard (2) to machine frame (4).
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7505     Mobile Transmission Jack (Low Lift)     1    
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Illustration 1 g00809285
Use Tooling (A) and support the bottom guard that will be installed. The weight of the bottom guards is approximately 45 kg (100 lb) to 84 kg (185 lb).
Illustration 2 g00809287
Install pin (6), nuts (4), and the washers that attach bottom guard (3) to both sides of machine frame (5) .
Move Tooling (A) and support the next bottom guard, as needed. Repeat Step 1 to Step 2 and install the bottom guards with pivot pin assembly.
Illustration 3 g00701916
Use Tooling (A) and a suitable block to install the front bottom guard.
Install bolts (2) and the washers. Install nuts (1) and the washers.Raising Bottom Guards
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-9200     Lever Puller     1    
Illustration 4 g00809277
Attach suitable lifting device (1) to one side of the machine. Attach Tooling (A) to the other side of the machine. Attach suitable lifting device (1) to Tooling (A) and pull tightly under bottom guard (2), as shown.
Illustration 5 g01205500
Use Tooling (A) to raise the bottom guard from ground level. The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids and debris. The bottom guard pivots on pin (5) .
Illustration 6 g00809278
Install nuts (3) on both sides that secure bottom guard (2) to machine frame (4).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts manifold Caterpillar catalog:
5N9222
MANIFOLD-PRESSURE
3126, 3208, 3304, 3304B, 3306, 3306B, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3412D, 3508, 3508C, 3512, 3512C, 3516, 3516B, G3304, G3306, G3306B, G3406, G3408, G3412, G3508, G3512, G3516, G399
3126, 3208, 3304, 3304B, 3306, 3306B, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3412D, 3508, 3508C, 3512, 3512C, 3516, 3516B, G3304, G3306, G3306B, G3406, G3408, G3412, G3508, G3512, G3516, G399
4W3219
MANIFOLD AS
G3512
G3512
4W3217
MANIFOLD AS
G3512
G3512
4P1451
MANIFOLD AS
G3512
G3512
4P1452
MANIFOLD AS
G3512
G3512
4P1453
MANIFOLD AS
G3512
G3512
4P1454
MANIFOLD AS
G3512
G3512
2W4594
MANIFOLD AS
G3512
G3512
3805148
MANIFOLD GP-EXHAUST
3512, 3512B, 3512C, 3516
3512, 3512B, 3512C, 3516
3482768
MANIFOLD GP-EXHAUST
854K, 992K, 993K
854K, 992K, 993K
1603624
MANIFOLD GP-HYDRAULIC
797, 797B, 797F
797, 797B, 797F
3N1688
MANIFOLD GP-WATER COOLED EXH
D398, D398A, D398B
D398, D398A, D398B
1772193
MANIFOLD GP-EJECTOR CONTROL
D400E II
D400E II