5D8755 MASTER CYLINDER KIT Caterpillar parts
120, 120B
Rating:
Alternative (cross code) number:
CA5D8755
5D-8755
5D8755
CA5D8755
5D-8755
5D8755
Weight: 0.24 pounds 0 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
5D8755 Master Cylinder KIT (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 0.44 lbs || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 0.44 lbs || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
CTP 3H5454 Valve Assembly for Model 5D8755 Cylinder Kit
CTP For Model 5D8755 Cylinder Kit || Highly Efficient || Easy in-and-out fit
CTP For Model 5D8755 Cylinder Kit || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02879298
Illustration 2 g02879337
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Remove bolts (3) from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb).
Remove bolts (2) from flywheel housing (1).
Remove bolts (4) from flywheel housing (1).
Use the suitable lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 3 g02879456
If necessary, remove dowels (5). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 2
B - Loctite 5970 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 4 g02881996
Illustration 5 g02879298
Illustration 6 g02879337
Clean the rear face of the cylinder block.
If necessary, install dowels (5) to the cylinder block.
Apply a 3mm bead of Tooling (B) in Position (Y) to the cylinder block as shown in Illustration 4.
Install Tooling (A) into the cylinder block in Positions (X).
Install a suitable lifting device onto the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb).
Use the suitable lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (4) and bolts (2) finger tight.
Remove Tooling (A). Install bolts (3) finger tight.
Tighten bolts (4) and bolts (2) to a torque of 110 N m (81 lb ft).
Tighten bolts (3) to a torque of 35 N m (26 lb ft).
Check the alignment of flywheel housing (1) with the crankshaft. Refer to System Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for more information.
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure. End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02879298
Illustration 2 g02879337
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Remove bolts (3) from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb).
Remove bolts (2) from flywheel housing (1).
Remove bolts (4) from flywheel housing (1).
Use the suitable lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 3 g02879456
If necessary, remove dowels (5). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 2
B - Loctite 5970 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 4 g02881996
Illustration 5 g02879298
Illustration 6 g02879337
Clean the rear face of the cylinder block.
If necessary, install dowels (5) to the cylinder block.
Apply a 3mm bead of Tooling (B) in Position (Y) to the cylinder block as shown in Illustration 4.
Install Tooling (A) into the cylinder block in Positions (X).
Install a suitable lifting device onto the flywheel housing. The weight of the flywheel housing is approximately 40 kg (88 lb).
Use the suitable lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (4) and bolts (2) finger tight.
Remove Tooling (A). Install bolts (3) finger tight.
Tighten bolts (4) and bolts (2) to a torque of 110 N m (81 lb ft).
Tighten bolts (3) to a torque of 35 N m (26 lb ft).
Check the alignment of flywheel housing (1) with the crankshaft. Refer to System Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for more information.
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure. End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts master Caterpillar catalog:
120, 120B, 12E
3D9137
MASTER CYLINDER ASSEMBLY
120, 12F, 140, 14E
120, 12F, 140, 14E
6D0175
MASTER POWER CYLINDER ASSEMBLY
120, 12F, 140, 14E
120, 12F, 140, 14E
140B, 14E
9W1845
MASTER SHOE
D11N
D11N
9W1847
MASTER SHOE
D11N
D11N
0775644
MASTER CYL A
Caterpillar
Caterpillar
0773570
MASTER BRAKE
Caterpillar
Caterpillar
0683602
MASTER CYL G
Caterpillar
Caterpillar
0605950
MASTER CYL
Caterpillar
Caterpillar
0602492
MASTER CYL
Caterpillar
Caterpillar
0333639
MASTER SEALS
Caterpillar
Caterpillar