1222052 MIRROR AS Caterpillar parts
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
Rating:
Alternative (cross code) number:
CA1222052
122-2052
1222052
CA1222052
122-2052
1222052
Weight: 2 pounds 0 kg.
BACKHOE LOADER,
Compatible equipment models: 1222052:
Number on catalog scheme:
2
For full view, you need register
Information:
Results
OK - The harness wiring, connectors, and seals are in good condition. Proceed to "Check the Wires for Damage to the Insulation".NOT OK - A problem has been found with the harness or the connectors.Repair
Repair the connectors or the wiring, as required. Ensure that all of the seals are properly in place. Ensure that the connectors have been reattached. If corrosion is evident on the pins, sockets or the connector, use only denatured alcohol to remove the corrosion. Use a cotton swab or a soft brush to remove the corrosion. If moisture was found in the connectors, run the engine for several minutes and check again for moisture. If moisture reappears, the moisture is wicking into the connector. Even if the moisture entry path is repaired, the wires may still need replaced. Verify that the repair eliminates the problem.STOPCheck the Wires for Damage to the Insulation
Carefully inspect each wire for signs of abrasion, of nicks, and of cuts. Inspect the wires for the following conditions:
Exposed insulation.
Rubbing of a wire against the chassis.
Rubbing of a wire against a sharp point.
Check all of the wiring harness fasteners in order to verify that the harness is properly secured. Also check all of the fasteners and verify that the harness is not compressed. Pull back the harness sleeves to check for a flattened portion of wire. A fastener that has been overtightened will flatten the harness. This damages the wires that are inside the harness. Expected Result
The wires are free of abrasion, of nicks, and of cuts and the harness is properly clamped.Results
OK - The harness is OK. Proceed to "Inspect the Connector Terminals".NOT OK - There is damage to the harness.Repair
Repair the wires or replace the wires, as required. Verify that the repair eliminates the problem.STOPInspect the Connector Terminals
A. Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are properly aligned in the connector and verify that the terminals are properly located in the connector.Expected Result
The terminals are properly aligned and the terminals appear undamaged.Results
OK - The terminals are OK. Proceed to "Expected
OK - The harness wiring, connectors, and seals are in good condition. Proceed to "Check the Wires for Damage to the Insulation".NOT OK - A problem has been found with the harness or the connectors.Repair
Repair the connectors or the wiring, as required. Ensure that all of the seals are properly in place. Ensure that the connectors have been reattached. If corrosion is evident on the pins, sockets or the connector, use only denatured alcohol to remove the corrosion. Use a cotton swab or a soft brush to remove the corrosion. If moisture was found in the connectors, run the engine for several minutes and check again for moisture. If moisture reappears, the moisture is wicking into the connector. Even if the moisture entry path is repaired, the wires may still need replaced. Verify that the repair eliminates the problem.STOPCheck the Wires for Damage to the Insulation
Carefully inspect each wire for signs of abrasion, of nicks, and of cuts. Inspect the wires for the following conditions:
Exposed insulation.
Rubbing of a wire against the chassis.
Rubbing of a wire against a sharp point.
Check all of the wiring harness fasteners in order to verify that the harness is properly secured. Also check all of the fasteners and verify that the harness is not compressed. Pull back the harness sleeves to check for a flattened portion of wire. A fastener that has been overtightened will flatten the harness. This damages the wires that are inside the harness. Expected Result
The wires are free of abrasion, of nicks, and of cuts and the harness is properly clamped.Results
OK - The harness is OK. Proceed to "Inspect the Connector Terminals".NOT OK - There is damage to the harness.Repair
Repair the wires or replace the wires, as required. Verify that the repair eliminates the problem.STOPInspect the Connector Terminals
A. Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are properly aligned in the connector and verify that the terminals are properly located in the connector.Expected Result
The terminals are properly aligned and the terminals appear undamaged.Results
OK - The terminals are OK. Proceed to "Expected
Cat SIS web machinery list:
Parts mirror Caterpillar catalog:
1641155
MIRROR GP-REAR VIEW
416D, 420D, 430D, 446D
416D, 420D, 430D, 446D
9R9758
MIRROR GP-REAR VIEW
416B, 416C, 426B, 426C, 428B, 436B, 436C, 438B, 446B
416B, 416C, 426B, 426C, 428B, 436B, 436C, 438B, 446B
9R6144
MIRROR GP-REAR VIEW
416, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436B, 436C, 438, 438B, 438C, 446, 446B
416, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436B, 436C, 438, 438B, 438C, 446, 446B
1222054
MIRROR GP-REAR VIEW
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1597107
MIRROR GP-REAR VIEW
416C, 426C, 428C, 436C, 438C, 446B
416C, 426C, 428C, 436C, 438C, 446B
1641055
MIRROR GP-REAR VIEW
416D, 420D, 424D, 428D, 432D, 438D, 442D
416D, 420D, 424D, 428D, 432D, 438D, 442D
2012638
MIRROR AS
303.5D, 303.5E, 303E CR, 304D CR, 304E, 305.5D, 305.5E, 305D CR, 305E, 416B, 416C, 426C, 428B, 436C, 446B, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
303.5D, 303.5E, 303E CR, 304D CR, 304E, 305.5D, 305.5E, 305D CR, 305E, 416B, 416C, 426C, 428B, 436C, 446B, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
7X0800
MIRROR AS
416C, 426C, 428B, 428C, 436, 436C, 438C, 446, 446B, IT12B, RT100, RT50, TH103, TH62, TH63, TH82, TH83
416C, 426C, 428B, 428C, 436, 436C, 438C, 446, 446B, IT12B, RT100, RT50, TH103, TH62, TH63, TH82, TH83
1222053
MIRROR AS
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1236620
MIRROR AS
416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 450E, 902, 904B, 906, 908, 914G, 924G, 924GZ, 930G, IT14G, IT28G
416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 450E, 902, 904B, 906, 908, 914G, 924G, 924GZ, 930G, IT14G, IT28G
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428E, 428F, 430D, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 446D, 450E, 450F, CB-44B, CB-54B, CD-54, CD-54B, CW-34
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, TH103, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B, TH62, TH63, TH82, TH83
216, 216B, 216B3, 226B, 226B3, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247B, 247B3, 248, 252B, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272...
1382314
MIRROR
65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E
65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E
1165776
MIRROR AS
35, 45, 55
35, 45, 55
35, 45, 55
35, 45, 55, 65E, 75E, 85E, 95E, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 30/30, 416B, 428, 517, 527, 583T, 587R, 587T, 613G, 621H, 621K, 623H, 623K, 62...
2044486
MIRROR
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1641955
MIRROR AS
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1236620
MIRROR AS
416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 450E, 902, 904B, 906, 908, 914G, 924G, 924GZ, 930G, IT14G, IT28G
416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 450E, 902, 904B, 906, 908, 914G, 924G, 924GZ, 930G, IT14G, IT28G
1222053
MIRROR AS
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D