AVSPARE.COM
parts catalog

MIRROR GP-REAR VIEW 2390270 - Caterpillar



2390270 MIRROR GP-REAR VIEW Caterpillar parts 824H, 825H, 826H MIRROR
Rating:
19
Alternative (cross code) number:
CA2390270
239-0270
2390270
Caterpillar 2390270 MIRROR GP-REAR VIEW

Buy MIRROR GP-REAR VIEW 2390270 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, WHEEL DOZER,

Compatible equipment models: 2390270:

LANDFILL COMPACTOR  826H  
SOIL COMPACTOR  825H  
WHEEL DOZER  824H   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 6 g00792279
Top of Main Control Valve (39) Implement pressure switch
Illustration 7 g00795482
Top of Main Control Valve (40) Connector
Disconnect connector (40) that is for implement pressure switch (39) .
Install 190-0163 Harness in place of connector (40) .
Illustration 8 g00795484
Underneath Engine (41) Connector (42) Engine speed sensor
Disconnect connector (41) for engine speed sensor (42) .Note: Performing Step 1 and Step 3 fixes the power shift pressure at 1270 kPa (185 psi).
Start the engine.
Place the engine speed dial in the HIGH IDLE position. Maintain the maximum no-load speed at 1980 50 rpm with the manual low idle switch OFF.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Check pressure tap (21) and make sure that the power shift pressure is 1270 290 kPa (185 40 psi).
In order to perform flow measurements for either one of the pumps, the other pump must be under load. To place the other pump under load, the main relief valve must be temporarily set to 22600 kPa (3275 psi) and an implement must be actuated while the pump flow test is performed.ReferenceRefer to Testing and Adjusting, "Relief Valve (Main) Test and Adjust" for the procedure to temporarily set the pressure of the main relief valve.
Turn valve (23) on the portable hydraulic tester clockwise. Record pump flow at each of the following pressures in Table 3. Use pressure tap (19) to monitor right pump delivery pressure or use pressure tap (20) to monitor left pump delivery pressure.
Illustration 9 g00797529
P-Q Characteristic Curve
Table 2
Pump Flow Test    
   Measuring Points    
9800 kPa (1425 psi)
20600 kPa (3000 psi)    
23500 kPa (3400 psi)    
29400 kPa (4250 psi)    
Flow measured liter/min (US gpm)     Right Pump                    
Left Pump                
Oil temperature °C (°F)                    
           
Engine speed (rpm)                    
           
Flow corrected liter/min (US gpm)     Right Pump                    
Left Pump                
Specification for flow rate liter/min (US gpm)     New    
93 4 (24.5 1.05)    
64 5 (16.9 1.3)    
58 4 (15.3 1.05)    
51 4 (13.5 1.05)    
Service limit
76 (20.1)    
53 (14)    
45 (11.9)    
40 (10.6)    Note: Specifications for output flow rates are based on an engine speed of 1800 rpm. To attain more accurate test results, measured flow should be corrected with the following calculation.
Table 3
Corrected flow     =     Measured flow x 1800 rpm    
measured rpm Note: The output flow rate changes approximately 3 L/min (0.8 US gpm) for each 100

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
825H Soil Compactor AZW00001-UP (MACHINE) POWERED BY C15 Engine
826H Landfill Compactor AWF00001-UP (MACHINE) POWERED BY C15 Engine
824H Wheel Dozer ASX00001-UP (MACHINE) POWERED BY C15 Engine


Parts mirror Caterpillar catalog:

1663416 MIRROR GP-REAR VIEW
824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 962G, 966G, 972G, 980G, 988G, 988H, IT62G
1151527 MIRROR GP-REAR VIEW
824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 962G, 966G, 972G, 980G, 988G, 988H, IT62G
1663417 MIRROR GP-REAR VIEW
824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 962G, 966G, 972G, 980G, 988G, 988H, IT62G
2390272 MIRROR GP-REAR VIEW
824H, 825H, 826H, 834H, 834K, 836H, 836K
5P6879 MIRROR
215B, 215D, 225, 229D, 235, 24H, 24M, 325, 325 L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5...
2755588 MIRROR AS
2470C, 2570C, 2670C, 2864C, 525D, 535D, 545D, 553C, 555D, 563C, 573C, 586C, 785C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797B, 797F, 814F II, 815F II, 816F II,...
8Y4512 MIRROR
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
3117058 MIRROR GP
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797B, 797F
3000560 MIRROR GP-REAR VIEW
770, 772, 773F, 775F, 777F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.