AVSPARE.COM
parts catalog

MIRROR GP-REAR VIEW 2390272 - Caterpillar



2390272 MIRROR GP-REAR VIEW Caterpillar parts 824H, 825H, 826H, 834H, 834K, 836H, 836K MIRROR
Rating:
22
Alternative (cross code) number:
CA2390272
239-0272
2390272
Caterpillar 2390272 MIRROR GP-REAR VIEW

Buy MIRROR GP-REAR VIEW 2390272 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, WHEEL DOZER,

Compatible equipment models: 2390272:

LANDFILL COMPACTOR  826H   836H   836K  
SOIL COMPACTOR  825H  
WHEEL DOZER  824H   834H   834K   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Note: The Hystat transmission and the hydraulic system use a common tank.
Illustration 1 g06206866
The hydraulic filter is located on the right side of the machine. Open the access door on the right side of the machine.
Illustration 2 g03804358
Some components are removed for clarity
Remove the hydraulic filter element by using the following steps.
Place a pan under the filter.
Remove the drain plug. Then, loosen the filter housing with a strap type wrench to allow air entry into the filter housing to allow for oil drainage.
Allow some time for complete drainage of oil from the filter housing.
Remove the filter housing from the oil filter base.
Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
Replace a new filter element into the housing. Apply a light coat of oil to the gasket of the new filter element.
Install the filter housing onto the filter base. When the gasket contacts the filter element mounting base, tighten the housing to a torque of 40 5 N m (30 4 lb ft). Use a 32 mm (1.25 inch) box end wrench.
Install the drain plug. Tighten to a torque of 12.5 2.5 N m (9.2 1.8 lb ft)
Illustration 3 g03803970
Maintain the hydraulic oil level so the oil is visible in the sight gauge . Add oil, if necessary.Reference: See Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for additional information.
Inspect the gasket on the cap for damage. Replace the gasket, if necessary.
Illustration 4 g03803895
Install the cap.
Close the access door.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
836H Landfill Compactor BXD00001-UP (MACHINE) POWERED BY C18 Engine
826H Landfill Compactor AWF00001-UP (MACHINE) POWERED BY C15 Engine


Parts mirror Caterpillar catalog:

3622574 MIRROR GP-REAR VIEW
CB-44B, CB-54B, CD-54B, CW-34
2228425 MIRROR GP-REAR VIEW
550B, 560B, 570B, 580B
3820848 MIRROR GP-REAR VIEW
525D, 535D, 545D, 555D
2458818 MIRROR GP-REAR VIEW
950H, 962H, 966H, 972H, 980H, IT62H
2482939 MIRROR GP-REAR VIEW
D10T, D10T2, D11T, D8T, D9R, D9T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.