2997570 MIRROR GP-REAR VIEW Caterpillar parts
789C
Rating:
Alternative (cross code) number:
CA2997570
299-7570
2997570
CA2997570
299-7570
2997570
TRUCK,
Compatible equipment models: 2997570:
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611570
Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
Install idler shaft (5) onto the cylinder block.Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when these marks are in alignment.
Install idler gear (3) onto the idler shaft.
Illustration 4 g00611568
Install thrust plate (2) onto the idler shaft.
Install the washer and idler gear bolt (1) onto thrust plate (2). Tighten idler gear bolt (1) to a torque of 34 5 N m (25 4 lb ft).Note: For more information, refer to Specifications, "Gear Group (Front)".Note: See the following list for the installation of the other gears in the front gear group.
In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft - Install".
In order to install the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
In order to install the gear from the engine oil pump, refer to Disassembly and Assembly, "Engine Oil Pump - Install".
In order to install the crankshaft front gear, refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install".End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611570
Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
Install idler shaft (5) onto the cylinder block.Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when these marks are in alignment.
Install idler gear (3) onto the idler shaft.
Illustration 4 g00611568
Install thrust plate (2) onto the idler shaft.
Install the washer and idler gear bolt (1) onto thrust plate (2). Tighten idler gear bolt (1) to a torque of 34 5 N m (25 4 lb ft).Note: For more information, refer to Specifications, "Gear Group (Front)".Note: See the following list for the installation of the other gears in the front gear group.
In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft - Install".
In order to install the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
In order to install the gear from the engine oil pump, refer to Disassembly and Assembly, "Engine Oil Pump - Install".
In order to install the crankshaft front gear, refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install".End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts mirror Caterpillar catalog:
785C, 785D, 789C, 789D
5110B, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793, 793B, 793C, 793D, AD45, AD55
784B, 784C, 785C, 789, 789B, 789C
785C, 785D, 789C, 789D, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F
773D, 773E, 776D, 777D, 789C
2361533
MIRROR GP-REAR VIEW
301.5, 301.6C, 302.5, 302.5C
301.5, 301.6C, 302.5, 302.5C
1466418
MIRROR GP-REAR VIEW
301.5, 302.5
301.5, 302.5
1466417
MIRROR GP-REAR VIEW
301.5, 302.5
301.5, 302.5
1623873
MIRROR GP-REAR VIEW
902, 906, 908
902, 906, 908
1792564
MIRROR GP-REAR VIEW
550, 570, 580
550, 570, 580
1660465
MIRROR GP-REAR VIEW
550, 570, 580
550, 570, 580