3599065 MODULE AR-CLEAN EMISSIONS Caterpillar parts
C4.4, CW-34
Rating:
Alternative (cross code) number:
CA3599065
359-9065
3599065
CA3599065
359-9065
3599065
INDUSTRIAL ENGINE, PNEUMATIC COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$180.00
01 Apr 2022
CN: Tiankon store
New Turbo Cartridge CHRA 4027065 for Cummins HX30, HX30W 2835399, 4039338, 4039339 3592312, 3592311, 3598047, 3598048, 3599240, 3599253, 3599065, 3599599, 3599600, 3599064
TKParts Application : For Cummins Various DFM HOLSET HX30 Turbos: 2835399, 4039338, 4039339 HOLSET HX30W Turbos: 3592312, 3592311, 3598047, 3598048, 3599240, 3599253, 3599065, 3599599, 3599600, 3599064
TKParts Application : For Cummins Various DFM HOLSET HX30 Turbos: 2835399, 4039338, 4039339 HOLSET HX30W Turbos: 3592312, 3592311, 3598047, 3598048, 3599240, 3599253, 3599065, 3599599, 3599600, 3599064
Number on catalog scheme:
1
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 140-7742 Protective Sleeve 4
B 1U-8233 Nylon Lifting Sling 4
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.Note: This procedure is a typical example.
Illustration 1 g00578366
Install Tooling (A) and Tooling (B) to the dump body. Attach an appropriate hoist.
Place dump body (4) into position on the machine. The weight of the dump body is 4357 kg (9606 lb).
Illustration 2 g00578667
Align the pivot points on the dump body with the pivot points on the frame. Lubricate pin assemblies (5). Install shims (C) and install the pin assemblies.Note: Install the shims equally. Install the shims in order to remove an excess amount of clearance between the pivot points. Install the shims between the pivot points, as shown above. Install the shims and the pin assemblies on opposite sides of the same plate.Note: It may be necessary to use a socket and a hammer in order to install the pin assemblies.
Illustration 3 g00578642
Install two bolts (3), the washers, and the nuts.
Illustration 4 g00582449
If necessary, adjust shims (D) .Note: Use the hoist and the lifting slings at the front of the dump body. Lift the front of the dump body and install the body prop. Adjust the shims in order to allow the body to sit evenly.
If necessary, adjust shims (E) .Note: Adjust shims in order to allow a clearance of 2.5 .5 mm (0.098 0.02 inch) between the guide plates and the chassis.
Illustration 5 g00578362
Install rear lights (2) .
Connect the electrical connections for lights (2) .
Install two bolts (1), the washers, and the nuts.
Remove Tooling (A) and Tooling (B) from the truck body.
Use the grease fittings on the pin assemblies in order to lubricate the pivot points.End By:
Install the tailgate cylinder. See Disassembly and Assembly, "Tailgate Cylinder - Install".
Install the hoist cylinders. Refer to Disassembly and Assembly, "Hoist Cylinder - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 140-7742 Protective Sleeve 4
B 1U-8233 Nylon Lifting Sling 4
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.Note: This procedure is a typical example.
Illustration 1 g00578366
Install Tooling (A) and Tooling (B) to the dump body. Attach an appropriate hoist.
Place dump body (4) into position on the machine. The weight of the dump body is 4357 kg (9606 lb).
Illustration 2 g00578667
Align the pivot points on the dump body with the pivot points on the frame. Lubricate pin assemblies (5). Install shims (C) and install the pin assemblies.Note: Install the shims equally. Install the shims in order to remove an excess amount of clearance between the pivot points. Install the shims between the pivot points, as shown above. Install the shims and the pin assemblies on opposite sides of the same plate.Note: It may be necessary to use a socket and a hammer in order to install the pin assemblies.
Illustration 3 g00578642
Install two bolts (3), the washers, and the nuts.
Illustration 4 g00582449
If necessary, adjust shims (D) .Note: Use the hoist and the lifting slings at the front of the dump body. Lift the front of the dump body and install the body prop. Adjust the shims in order to allow the body to sit evenly.
If necessary, adjust shims (E) .Note: Adjust shims in order to allow a clearance of 2.5 .5 mm (0.098 0.02 inch) between the guide plates and the chassis.
Illustration 5 g00578362
Install rear lights (2) .
Connect the electrical connections for lights (2) .
Install two bolts (1), the washers, and the nuts.
Remove Tooling (A) and Tooling (B) from the truck body.
Use the grease fittings on the pin assemblies in order to lubricate the pivot points.End By:
Install the tailgate cylinder. See Disassembly and Assembly, "Tailgate Cylinder - Install".
Install the hoist cylinders. Refer to Disassembly and Assembly, "Hoist Cylinder - Install".
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts module Caterpillar catalog:
3513434
MODULE GP-SPEED & VIBRATORY
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
3224709
MODULE GP-SPEED
CB-54
CB-54
3515796
MODULE GP-DISPLAY
PM-102
PM-102
1666943
MODULE GP-QUAD GAUGE
365B, 365B II, 365B L, 385B, 5090B, 5110B, AP-1055D, AP-655C, BG-2455D, BG-260D, PM-465, TK1051
365B, 365B II, 365B L, 385B, 5090B, 5110B, AP-1055D, AP-655C, BG-2455D, BG-260D, PM-465, TK1051
5110B, PM-465
CB-525B
1G4501
MODULE AR
CB-525B
CB-525B
1104438
MODULE GP-SPEED
PS-500
PS-500
8C0205
MODULE GP-SPEED
PS-500
PS-500
0848330
MODULE AR
CB-521, CB-525B
CB-521, CB-525B
3630556
MODULE AR-CLEAN EMISSIONS
CB-44B, CB-54B
CB-44B, CB-54B