20R7975 MONITOR GP-OPR Caterpillar parts
Rating:
Alternative (cross code) number:
CA20R7975
20R-7975
20R7975
CA20R7975
20R-7975
20R7975
Weight: 2 pounds 1 kg.
Related part:
1519385
MONITOR GP-OPR
20R7975
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Qyljday Monitor 20R-7975 20R7975 CA20R7975 fits for Caterpillar Excavator 325BL
Qyljday Part#:20R-7975 || Application:Fits for Caterpillar Excavator 325BL || Please confirm your part number before purchasing, different part numbers correspond to different procedures. || Guaranteed Exact Fit for easy installation || Longer Service Life
Qyljday Part#:20R-7975 || Application:Fits for Caterpillar Excavator 325BL || Please confirm your part number before purchasing, different part numbers correspond to different procedures. || Guaranteed Exact Fit for easy installation || Longer Service Life
HAOSHUN Monitor Compatible for Caterpillar Excavator CAT 325BL 20R-7975
HAOSHUN Part Name:Monitor || Part Number:20R-7975 20R7975 || APPlication: Compatible FOR Caterpillar Excavator CAT 325BL || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
HAOSHUN Part Name:Monitor || Part Number:20R-7975 20R7975 || APPlication: Compatible FOR Caterpillar Excavator CAT 325BL || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
Pmtihxu Monitor 20R-7975 20R7975 For Caterpillar CAT Excavator 325BL
Pmtihxu Part Number: 20R-7975 20R7975 || Item Name: Monitor || For Caterpillar CAT 325BL Excavator || Warranty: 6 months || Note: Please check both part number and models before you buy it to make sure this part will fit !
Pmtihxu Part Number: 20R-7975 20R7975 || Item Name: Monitor || For Caterpillar CAT 325BL Excavator || Warranty: 6 months || Note: Please check both part number and models before you buy it to make sure this part will fit !
For full view, you need register
Information:
Remove Sprockets
Start By:a. separation of tracks1. Remove the oil from the final drive housing. 2. Remove bolts (1) and locknut (2). 3. Remove nut (3) from the sprocket shaft. 4. Install tooling (A) as shown. Make sure there is .250 in. (6.35 mm) clearance between 6F8343 Adapter (5) and sprocket (4). Fasten a hoist to tooling (A). Loosen sprocket (4) from the sprocket shaft.
Do not remove 6F8343 Adapter (5) or the sprocket can fall when the tooling is removed.
5. Remove tooling (A) except for 6F8343 Adapter (5). Fasten a hoist to the sprocket as shown. Remove 6F8343 Adapter (5) from the sprocket shaft. 6. Remove sprocket (4). The weight is 52 kg (115 lb.). 7. Remove gasket (6) from the sprocket. 8. Remove outer half of Duo-Cone seal (7) from the sprocket. 9. Remove inner half of Duo-Cone seal (8) from the retainer.Install Sprockets
See Installation Of Duo-Cone Floating Seals before installing any of the Duo-Cone Seals.
1. Install the inner half of the Duo-Cone seal with tool (A) in the retainer. 2. Install the outer half of the Duo-Cone seal with tool (A) in the sprocket.
The splines in the sprocket and shaft must be clean and free from burrs.
3. Fasten a hoist to the sprocket. Put sprocket (1) in position on the sprocket shaft. 4. Install tooling (B) and fasten a hoist. Use tooling (B) to install the sprocket on the sprocket shaft with a force of 311 to 355 kN (35 to 40 ton). 5. Use tooling (C) to check the distance from the shoulder of the sprocket shaft to the face of the sprocket. The distance must be 3.00 0.8 mm (118 .03 in.). 6. Install gasket (2). 7. Install the nut that holds the sprocket on the sprocket shaft. Tighten the nut to a torque of 334 33 N m (243 24 lb. ft.). 8. Put 7M7260 Liquid Gasket Material between locknut (4) and the sprocket face. Install locknut (4). If the bolt holes do not make an alignment with the holes in the sprocket, turn nut (3) clockwise only to install locknut (4).9. Fill the final drive housing with oil to the correct level. See MAINTENANCE GUIDE.End By:a. connection of tracks
Start By:a. separation of tracks1. Remove the oil from the final drive housing. 2. Remove bolts (1) and locknut (2). 3. Remove nut (3) from the sprocket shaft. 4. Install tooling (A) as shown. Make sure there is .250 in. (6.35 mm) clearance between 6F8343 Adapter (5) and sprocket (4). Fasten a hoist to tooling (A). Loosen sprocket (4) from the sprocket shaft.
Do not remove 6F8343 Adapter (5) or the sprocket can fall when the tooling is removed.
5. Remove tooling (A) except for 6F8343 Adapter (5). Fasten a hoist to the sprocket as shown. Remove 6F8343 Adapter (5) from the sprocket shaft. 6. Remove sprocket (4). The weight is 52 kg (115 lb.). 7. Remove gasket (6) from the sprocket. 8. Remove outer half of Duo-Cone seal (7) from the sprocket. 9. Remove inner half of Duo-Cone seal (8) from the retainer.Install Sprockets
See Installation Of Duo-Cone Floating Seals before installing any of the Duo-Cone Seals.
1. Install the inner half of the Duo-Cone seal with tool (A) in the retainer. 2. Install the outer half of the Duo-Cone seal with tool (A) in the sprocket.
The splines in the sprocket and shaft must be clean and free from burrs.
3. Fasten a hoist to the sprocket. Put sprocket (1) in position on the sprocket shaft. 4. Install tooling (B) and fasten a hoist. Use tooling (B) to install the sprocket on the sprocket shaft with a force of 311 to 355 kN (35 to 40 ton). 5. Use tooling (C) to check the distance from the shoulder of the sprocket shaft to the face of the sprocket. The distance must be 3.00 0.8 mm (118 .03 in.). 6. Install gasket (2). 7. Install the nut that holds the sprocket on the sprocket shaft. Tighten the nut to a torque of 334 33 N m (243 24 lb. ft.). 8. Put 7M7260 Liquid Gasket Material between locknut (4) and the sprocket face. Install locknut (4). If the bolt holes do not make an alignment with the holes in the sprocket, turn nut (3) clockwise only to install locknut (4).9. Fill the final drive housing with oil to the correct level. See MAINTENANCE GUIDE.End By:a. connection of tracks
Parts monitor Caterpillar catalog:
20R5129
MONITOR GP -A
Caterpillar
Caterpillar
20R5130
MONITOR GP -A
Caterpillar
Caterpillar
Caterpillar
20R7482
MONITOR GP-EXH
Caterpillar
Caterpillar
20R7481
MONITOR GP-EXH
Caterpillar
Caterpillar
20R7480
MONITOR GP-EXH
Caterpillar
Caterpillar
0991978
MONITOR
Caterpillar
Caterpillar
0978058
MONITOR AS-ODS
Caterpillar
Caterpillar
0961953
MONITOR A
Caterpillar
Caterpillar
0945945
MONITOR LAMP
Caterpillar
Caterpillar
0928482
MONITOR
Caterpillar
Caterpillar
0R5476
MONITOR GP-ELEC
Caterpillar
Caterpillar