AVSPARE.COM
parts catalog

MONITOR AR-PAYLOAD 2500943 - Caterpillar



2500943 MONITOR AR-PAYLOAD Caterpillar parts R2900G MONITOR
Rating:
19
Alternative (cross code) number:
CA2500943
250-0943
2500943
Caterpillar 2500943 MONITOR AR-PAYLOAD

Buy MONITOR AR-PAYLOAD 2500943 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP,

Compatible equipment models: 2500943:

LOAD HAUL DUMP  R2900G   Caterpillar
  For full view, you need register

Information:


Illustration 3 g00758414
Typical example
Install an appropriate nylon lifting sling to pin (5). Use an appropriate lifting device to lift the pin into position on the work tool. The weight of the pin is 33 kg (73 lb). Apply 4C-5598 High Temperature Anti-Seize to pin (5). Coat the threads and the smooth surface of the pin. Align the pin with the stops in the housing. Use a large hammer and a brass drift to install the pin. Remove the lifting sling after the pin is secure.
Illustration 4 g00758411
Typical example
Use Tooling (A) to install nut (4) on the pin. After you tighten the nut, back off the nut until the nearest set of holes are aligned. Install the two bolts and the washers that secure the nut to the housing.
Illustration 5 g00713580
Typical exampleThe jaw has been disconnected from the work tool for photographic clarity.
Align the lower pin hole. Use two adjusting bolts (10) to align the jaw with the lower housing. The bolts are located at the bottom of the jaw.
Illustration 6 g00758417
Typical example
Use a floor jack or an appropriate lifting device to lift pin (8) into position. The weight of the pin is 33 kg (73 lb). Apply 4C-5598 High Temperature Anti-Seize to pin (8). Coat the threads and the smooth surface of the pin. Align the pin with the stops in the housing. Use a large hammer and a brass drift to install the pin. Remove the lifting sling after the pin is secure.
Illustration 7 g00758425
Use Tooling (A) to install nut (7) on the pin. After you tighten the nut, back off the nut until the nearest set of holes are aligned. Install the two bolts and the washers that secure the nut to the housing.
Remove the hoist and the lifting chains from the work tool.
Illustration 8 g00713540
Typical example
Attach an appropriate nylon lifting sling and a hoist to the cylinder. Lower the cylinder into position in the jaw.
Illustration 9 g00713544
Typical example
Apply 4C-5598 High Temperature Anti-Seize to pin (2). Coat the threads and the smooth surface of the pin. Lift the pin into position in the work tool. The weight of the pin is 19 kg (42 lb). Align the pin with the stops in the housing. Use a large hammer and a brass drift to install pin (2) .
Illustration 10 g00711714
Typical example
Use Tooling (A) to install nut (1) on the pin. After you tighten the nut, back off the nut until the nearest set of holes are aligned. Install the two bolts and the washers that secure the nut to the jaw.
Illustration 11 g00758749
Typical example
Lubricate the pins. The grease fittings are located on the head of each pin.
Table 2
Weights of the Jaws    
Part Number     Description     Weight    
179-6757     Crusher Jaws    
1000 kg (2205 lb)    
179-6761     Combination Jaw    
1000 kg (2205 lb)    
179-6765     Primary Pulverizer Jaw    
1150 kg (2535 lb)    
179-6768     Secondary Pulverizer Jaw    
1050 kg (2315 lb)    
179-6772     Shear Jaw    
1000 kg (2205 lb)    
179-6780     Tank

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts monitor Caterpillar catalog:

2115618 MONITOR GP-OPERATOR
322C, 325C, 330C L, 330C MH
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.