AVSPARE.COM
parts catalog

MONITOR GP 4Z6577 - Caterpillar



4Z6577 MONITOR GP Caterpillar parts MONITOR
Rating:
71
Alternative (cross code) number:
CA4Z6577
4Z-6577
4Z6577
Caterpillar 4Z6577 MONITOR GP

Buy MONITOR GP 4Z6577 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Cat® ET
The Cat® Electronic Technician (Cat ET) service tool has the following attributes:
Used to troubleshoot a machine
Runs on a computer with Microsoft Windows
Displays diagnostic code information, including history and parameter status
Displays the key data link parameters (speeds, pressures, etc.)
Display of Totals and Histograms
Configuration of parameters for optional attachments
Allowing advanced features such as ECM replacement
Requires the tools listed in Table 1
Table 1
Service Tools
Part Number Part
JERD2129 Cat Electronic Technician (Cat) ET 2014B or later version
Computer
8T-3224 Needle Tip Group
7X-1710 Multimeter Probe Group
8T-8726 Cable Assembly (Three Pin) (3-Pin Breakout)
6V-3000 Connector Repair Kit (Sure Seal)
190-8900 Connector Repair Kit (Deutsch)
175-3700 Connector Repair Kit (Deutsch DT)
One of the Following Adaptors
317-7484 Communication Adapter Gp
349-1206 Kit-Radio (Wireless CA3)(1)
317-7492 Kit-Radio (Wireless CA3)(2)
One of the Following Digital Multimeters
237-5130
257-9140 Digital Multimeter
146-4080(3) Digital Multimeter Gp
(1) EAME Only
(2) NACD Only
(3) This multimeter can use an RS232C cable to connect to a Laptop computer or Dataview tool gp for troubleshooting.Reference: See the following for instructions:
Special Publication, JERD2124, "ET Single Use Program License"
Special Publication, JEHP1026, "Information and Requirements Sheet"
Data Subscription
Special Publication, JERD2142, "Data Subscription"
Special Publication, JEHP1026, "Information and Requirements Sheet"
Illustration 1 g03785357
Connections for the Communication Adapter III (CatET)
(1) Current version of Cat ET software
(2) 317-7484 Communication Adapter III
(3) Service diagnostic cable
(4) Cable Adaptors
One of the adapters listed in Table 1 is required to connect the computer to the machine. Reference: For wireless adaptor instructions, see Special Publication, NEHS1081, "317-7492 Wireless Radio".Reference: For Comm III adapter instructions, see Special Publication, NEHS1032, "Communications Adapter III".Connectors
Reference: See the following for connector information:
For Locations: Troubleshooting, "Electrical Components and Connector Locations" and the Electrical Schematic for the machine
For Sure Seal connector instructions, see Special Instruction, SMHS7531
For Deutsch DT connectors instructions, see Special Instruction, SEHS9615. .Multimeters
Use a calibrated digital multimeter to test continuity and voltage. Reference: See the multimeter manual provided with the multimeter. 7X-1710 Multimeter Probes are used to measure voltage at a connector without separating the connection. The probe cables are pushed into the back of a connector along the wire. The 8T-8726 Adapter Cable has a three pin breakout and is used for sensor circuit measurements.Note: Caterpillar recommends the use of a 8T-0500 Continuity Tester and a 5P-7277 Voltage Tester to test a harness. Caterpillar does not recommend the use of a 8T-0500 Continuity Tester or a 5P-7277 Voltage Tester for electronic circuits.


Parts monitor Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.