1648351 MOTOR GP-GEROTOR Caterpillar parts
P16
Rating:
Alternative (cross code) number:
CA1648351
164-8351
1648351
CA1648351
164-8351
1648351
PULVERIZER,
Compatible equipment models: 1648351:
For full view, you need register
Information:
Removal Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: The aftercooler has been removed for photographic purposes only.
Illustration 1 g00553070
Typical example
Disconnect hose assemblies (1) and tube assemblies (2).
Remove the O-ring seals. Cap all male fittings and plug all female fittings immediately after you remove the hose assemblies and the tube assemblies.
Illustration 2 g00553072
Typical example
Disconnect tube assembly (3). Remove the O-ring seals. Cap all male fittings and plug all female fittings immediately after you remove the tube assembly.
Remove bolt (5), the washer, and the nut. Remove clamp (4).
Remove bolt (6), the washer, and the spacer. Remove clamp (7). Remove tube assembly (3).
Illustration 3 g00553073
Typical example
Cut wire ties (8) and (9).
Illustration 4 g00553074
Typical example
Disconnect injection actuation pressure control valve (10).
Mark engine oil temperature sensor connector (11) and the connector for the engine oil pressure sensor (12) for identification purposes.
Disconnect engine oil temperature sensor connector (11) and the connector for the engine oil pressure sensor (12).
Illustration 5 g00553076
Typical example
Remove three bolts (13) and the washers.
Illustration 6 g00553109
Typical example
Attach a strap and a suitable lifting device to unit injector hydraulic pump (14). The weight of the unit injector hydraulic pump is approximately 30 kg (66 lb).
Illustration 7 g00553111
Typical example
Remove two bolts (15) and the washers. Remove unit injector hydraulic pump (14). Remove the O-ring seals.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: The aftercooler has been removed for photographic purposes only.
Illustration 1 g00553070
Typical example
Disconnect hose assemblies (1) and tube assemblies (2).
Remove the O-ring seals. Cap all male fittings and plug all female fittings immediately after you remove the hose assemblies and the tube assemblies.
Illustration 2 g00553072
Typical example
Disconnect tube assembly (3). Remove the O-ring seals. Cap all male fittings and plug all female fittings immediately after you remove the tube assembly.
Remove bolt (5), the washer, and the nut. Remove clamp (4).
Remove bolt (6), the washer, and the spacer. Remove clamp (7). Remove tube assembly (3).
Illustration 3 g00553073
Typical example
Cut wire ties (8) and (9).
Illustration 4 g00553074
Typical example
Disconnect injection actuation pressure control valve (10).
Mark engine oil temperature sensor connector (11) and the connector for the engine oil pressure sensor (12) for identification purposes.
Disconnect engine oil temperature sensor connector (11) and the connector for the engine oil pressure sensor (12).
Illustration 5 g00553076
Typical example
Remove three bolts (13) and the washers.
Illustration 6 g00553109
Typical example
Attach a strap and a suitable lifting device to unit injector hydraulic pump (14). The weight of the unit injector hydraulic pump is approximately 30 kg (66 lb).
Illustration 7 g00553111
Typical example
Remove two bolts (15) and the washers. Remove unit injector hydraulic pump (14). Remove the O-ring seals.
Parts motor Caterpillar catalog:
1453667
MOTOR & LINES GP-ROTATOR
CR20, P16
CR20, P16
1454021
MOTOR & LINES GP-ROTATOR
CR20, P16
CR20, P16
1609713
MOTOR & LINES GP-ROTATOR
CR20, P16
CR20, P16
1609714
MOTOR & LINES GP-ROTATOR
CR20, P16
CR20, P16
1609715
MOTOR & LINES GP-ROTATOR
CR20, P16
CR20, P16
1456153
MOTOR GP-GEROTOR
CR20, P16
CR20, P16
1609122
MOTOR GP-GEROTOR
CR20, P16
CR20, P16
1647282
MOTOR GP-GEROTOR
CR20, P16
CR20, P16
1856953
MOTOR GP-TRAVEL
311C, 313D2 LGP, 315C, 315D L, 316E L, 318D L, 318D2 L
311C, 313D2 LGP, 315C, 315D L, 316E L, 318D L, 318D2 L
2513263
MOTOR GP-WINDOW WIPER
953C, 963C, 973C
953C, 963C, 973C