2969346 MOTOR GP-PISTON Caterpillar parts
CB-214E, CB-22
Rating:
Alternative (cross code) number:
CA2969346
296-9346
2969346
CA2969346
296-9346
2969346
Weight: 68 pounds 31 kg.
VIBRATORY COMPACTOR,
This part in 6 request:
Show.
This information for suppliers only!
2024-09-27
2023-06-08
2020-08-14
2020-01-28
2017-01-12
2017-01-11
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly in order to relieve pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
To prevent dirt and contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected.This action also lessens the chance of oil spills.
The pressure in the accumulator for the parking brake must be discharged before removing the accumulator. Turn the ignition key to the on position. Install a pressure gauge on the pressure test port for the parking brake. The gauge must read pressure from zero to 3447 kPa (500 psi). Activate the parking brake switch to the on and the off positions repeatedly until the pressure in the gauge is at zero. Open the accumulator purge valve in order to verify that all of the pressure has been relieved.
Put identification marks on all lines, hoses, wires, and tubes for installation purposes. Plug all lines, hoses and tubes. This helps prevent fluid loss and contamination of the oil system.
Illustration 1 g00578537
Open the access door that is directly behind the cab. Disconnect hose (2) from accumulator (3). Remove the O-ring seal from the hose. Remove nut (1) that secures accumulator (3) to the mounting bracket.Installation Procedure
Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 2 g00578537
Position accumulator (3) to the mounting bracket. Install nut (1) that secures accumulator (3) to the mounting bracket.
Install the O-ring seal to hose (2). Connect hose (2) to accumulator (3) .
Close the access door.
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly in order to relieve pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
To prevent dirt and contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected.This action also lessens the chance of oil spills.
The pressure in the accumulator for the parking brake must be discharged before removing the accumulator. Turn the ignition key to the on position. Install a pressure gauge on the pressure test port for the parking brake. The gauge must read pressure from zero to 3447 kPa (500 psi). Activate the parking brake switch to the on and the off positions repeatedly until the pressure in the gauge is at zero. Open the accumulator purge valve in order to verify that all of the pressure has been relieved.
Put identification marks on all lines, hoses, wires, and tubes for installation purposes. Plug all lines, hoses and tubes. This helps prevent fluid loss and contamination of the oil system.
Illustration 1 g00578537
Open the access door that is directly behind the cab. Disconnect hose (2) from accumulator (3). Remove the O-ring seal from the hose. Remove nut (1) that secures accumulator (3) to the mounting bracket.Installation Procedure
Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 2 g00578537
Position accumulator (3) to the mounting bracket. Install nut (1) that secures accumulator (3) to the mounting bracket.
Install the O-ring seal to hose (2). Connect hose (2) to accumulator (3) .
Close the access door.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts motor Caterpillar catalog:
CB-214D, CB-214E, CB-224C
1563538
MOTOR & MTG GP-PROPEL
CB-214D, CB-214E
CB-214D, CB-214E
2453602
MOTOR GP-PISTON
CB-214D, CB-214E
CB-214D, CB-214E
3045602
MOTOR GP-PISTON
CB-214E
CB-214E
1563547
MOTOR & MTG GP-VIBRATORY
CB-214D, CB-214E, CB-22
CB-214D, CB-214E, CB-22
1569037
MOTOR GP-GEAR
CB-14, CB-214D, CB-214E, CB-22, CB-334E, CB-34
CB-14, CB-214D, CB-214E, CB-22, CB-334E, CB-34
3900804
MOTOR GP-GEAR
CB-14, CB-214D, CB-214E, CB-22, CB-334E, CB-34
CB-14, CB-214D, CB-214E, CB-22, CB-334E, CB-34
1563539
MOTOR & MTG GP-PROPEL
CB-214D, CB-214E
CB-214D, CB-214E
216, 228, 236, 236B, 242B, 247, 247B, 248, 267, 267B, 268B, 287, BU115, BU118, CB-14, CB-214D, CB-214E, CB-224C, CB-334D, CB-334E, CB-335D
1187434
MOTOR-MODULE
CB-214D, CB-214E, CB-224C, CB-334D, CB-334E, CB-335D
CB-214D, CB-214E, CB-224C, CB-334D, CB-334E, CB-335D
1797948
MOTOR AS-FAN
CB-214D, CB-214E, CB-22
CB-214D, CB-214E, CB-22
2967924
MOTOR GP-PISTON
CB-22
CB-22
CB-34
3108545
MOTOR GP-PISTON
AP-655D
AP-655D
3689118
MOTOR GP-GEAR
AP-600D, AP-655D, AS4252C
AP-600D, AP-655D, AS4252C
3238187
MOTOR & MTG GP-AUGER
AP555E, BG500E
AP555E, BG500E
3513396
MOTOR & MTG GP-PISTON
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
4342555
MOTOR GP-PISTON
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
3706072
MOTOR GP-PISTON
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
2997619
MOTOR & MTG GP-PROPEL
CB-54, CB-64
CB-54, CB-64
2942887
MOTOR GP-PISTON
AP-600D, BG500E, BG600D
AP-600D, BG500E, BG600D