3535934 MOTOR GP-PISTON Caterpillar parts
CP-74B, CS-74B, CS-76B, CS-78B
Rating:
Alternative (cross code) number:
CA3535934
353-5934
3535934
CA3535934
353-5934
3535934
Weight: 39 pounds 17 kg.
VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
HIlti 3535934 Floor Saw Blade DS-BF 26x187/1 MCS Diamond coring Sawing
HILTI Sold on Amazon
HILTI Sold on Amazon
HIlti 3535934 Floor Saw Blade DS-BF 26x187/1 MCS Diamond coring Sawing
HILTI Sold on Amazon
HILTI Sold on Amazon
Information:
Start By:
Remove the bottom guards.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Illustration 1 g00867666
Align sprocket segment (1) with the idler on the right side of the machine. Remove nuts (2) and the bolts. Remove sprocket segment (1). This procedure will allow the roller frame to pivot when the front of the machine is raised.
Illustration 2 g01218846
Lift the blade assembly and install Tooling (D) .
Illustration 3 g00867667
Use Tooling (C) to raise the machine. Place a 152 mm (6.0 inch) block under the left track. Lower the machine on the block until the weight is removed from the equalizer bar pins.
Illustration 4 g01218648
Typical Example
Illustration 5 g02355097
Use Tooling (B) and a suitable lifting device to support both ends of equalizer bar (3). The weight of equalizer bar (3) is approximately 102 kg (225 lb) to 259 kg (570 lb).
Illustration 6 g02355039
Remove bolts (4), guards (5), and pin (6). Repeat this step for the opposite side of the equalizer bar.
Illustration 7 g02355119
Disconnect grease hose assembly (7) and remove the fitting. Repeat this step for the opposite side.
Illustration 8 g02355122
Remove bolt (8), the washer, and the spacer.
Use Tooling (E) to remove center pin (9) .
Illustration 9 g01310247
Use Tooling (C) to raise the machine for removal of the equalizer bar.
Illustration 10 g02355156
Illustration 11 g02355158
Use Tooling (B) to raise the left side of equalizer bar (3). Lower the right side of equalizer bar (3) until the right side of equalizer bar (3) will clear the frame.
Lower the left side and remove equalizer bar (3). Installation Procedure
Install equalizer bar (3) in the reverse order of removal.
Remove the bottom guards.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Illustration 1 g00867666
Align sprocket segment (1) with the idler on the right side of the machine. Remove nuts (2) and the bolts. Remove sprocket segment (1). This procedure will allow the roller frame to pivot when the front of the machine is raised.
Illustration 2 g01218846
Lift the blade assembly and install Tooling (D) .
Illustration 3 g00867667
Use Tooling (C) to raise the machine. Place a 152 mm (6.0 inch) block under the left track. Lower the machine on the block until the weight is removed from the equalizer bar pins.
Illustration 4 g01218648
Typical Example
Illustration 5 g02355097
Use Tooling (B) and a suitable lifting device to support both ends of equalizer bar (3). The weight of equalizer bar (3) is approximately 102 kg (225 lb) to 259 kg (570 lb).
Illustration 6 g02355039
Remove bolts (4), guards (5), and pin (6). Repeat this step for the opposite side of the equalizer bar.
Illustration 7 g02355119
Disconnect grease hose assembly (7) and remove the fitting. Repeat this step for the opposite side.
Illustration 8 g02355122
Remove bolt (8), the washer, and the spacer.
Use Tooling (E) to remove center pin (9) .
Illustration 9 g01310247
Use Tooling (C) to raise the machine for removal of the equalizer bar.
Illustration 10 g02355156
Illustration 11 g02355158
Use Tooling (B) to raise the left side of equalizer bar (3). Lower the right side of equalizer bar (3) until the right side of equalizer bar (3) will clear the frame.
Lower the left side and remove equalizer bar (3). Installation Procedure
Install equalizer bar (3) in the reverse order of removal.
Caterpillar SIS machinery equipment:
Caterpillar SIS
CS74B CP74B Soil Compactor L7B00001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS78B Vibratory Soil Compactor L8C00001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS78B Compactor 44300001-UP (MACHINE) POWERED BY C6.6 Engine »
353-5934
MOTOR GP-PISTON
CS74B Compactor 44100001-UP (MACHINE) POWERED BY C6.6 Engine »
353-5934
MOTOR GP-PISTON
CS76B Vibratory Soil Compactor L9H00001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS74B, CP74B, and CS78B Compactor-Vibratory Soil E7E00001-UP (MACHINE) POWERED BY C6.6 Engine »
353-5934
MOTOR GP-PISTON
CS74B, CP74B Vibratory Compactor 49000001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS78B, CS76B Vibratory compactor 49200001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS76B, CS78B Vibratory Soil Compactor CB700001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS74B, CP74B Vibratory Soil Compactor CS400001-UP (MACHINE) POWERED BY C4.4 Engine »
353-5934
MOTOR GP-PISTON
CS79B Vibratory Soil Compactor C7900001-UP (MACHINE) POWERED BY C6.6 Engine »
353-5934
MOTOR GP-PISTON
CS74B, CP74B Vibratory Soil Compactor 51200001-UP (MACHINE) POWERED BY C7.1 Engine »
353-5934
MOTOR GP-PISTON
CS74B, CP74B Vibratory Soil Compactor B7M00001-UP (MACHINE) POWERED BY C7.1 Engine »
353-5934
MOTOR GP-PISTON
CS78B Vibratory Soil Compactor 51300001-UP (MACHINE) POWERED BY C7.1 Engine »
353-5934
MOTOR GP-PISTON
CS78B, CS79B Vibratory Soil Compactor CM700001-UP (MACHINE) POWERED BY C7.1 Engine »
353-5934
MOTOR GP-PISTON
CP76B Vibratory Soil Compactor J7600001-UP (MACHINE) POWERED BY C7.1 Engine »
353-5934
MOTOR GP-PISTON
Caterpillar parts catalog:
Parts motor Caterpillar catalog:
3597628
MOTOR GP-WINDOW WIPER
CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B, CW-34
CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B, CW-34
3556035
MOTOR & MTG GP-PROPEL
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
3535935
MOTOR GP-GEAR
CB-44B, CB-54B, CD-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-78B
CB-44B, CB-54B, CD-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-78B
3535924
MOTOR GP-PISTON
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
2202064
MOTOR GP-WINDOW WIPER
554, 564, 574B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
554, 564, 574B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
3544762
MOTOR & MTG GP-PROPEL
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
3535925
MOTOR GP-PISTON
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
3950521
MOTOR GP-GEAR
CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-68B, CS-74B, CS-76B, CS-78B
3556032
MOTOR & MTG GP-PISTON
CP-74B, CS-74B, CS-76B, CS-78B
CP-74B, CS-74B, CS-76B, CS-78B
1350611
MOTOR GP-WINDOW WIPER
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H...
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H...
3826587
MOTOR-STARTING
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, C4.4, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, C4.4, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B
2756706
MOTOR AS-BLOWER
583T, 587R, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 770, 770G, 770G OEM, 772, 772G, 772G OEM, 914G, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 930G...
583T, 587R, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 770, 770G, 770G OEM, 772, 772G, 772G OEM, 914G, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 930G...
3G8635
MOTOR GP-GEAR
578, 583R, 589
578, 583R, 589
4425642
MOTOR GP-PISTON
279C, 279D, 289C, 289D, 299D, 299D XHP
279C, 279D, 289C, 289D, 299D, 299D XHP
1207068
MOTOR & MTG GP-PROPEL
PS-150B
PS-150B
2309597
MOTOR & MTG GP-AUGER
AP-1055D, AP-600D, AP-655D, BG-2455D, BG-260D, BG600D, BG655D
AP-1055D, AP-600D, AP-655D, BG-2455D, BG-260D, BG600D, BG655D
1794809
MOTOR GP-WINDOW WIPER
D3G, D4G, D5G
D3G, D4G, D5G
4191673
MOTOR GP-PISTON
CW-14, PS-150C
CW-14, PS-150C
3540593
MOTOR GP-PISTON
120M, 120M 2, 12M 2, 12M 3 AWD, 140M, 140M 2, 140M 3 AWD, 160M, 160M 2, 160M 3 AWD
120M, 120M 2, 12M 2, 12M 3 AWD, 140M, 140M 2, 140M 3 AWD, 160M, 160M 2, 160M 3 AWD
4561649
MOTOR GP-PISTON
525D, 535D, 545D, 555D
525D, 535D, 545D, 555D
3676592
MOTOR & MTG GP-PROPEL
CB34B, CB34B XW, CC34B
CB34B, CB34B XW, CC34B
1874127
MOTOR GP-PISTON
322B L, 322C, 324D FM, 325B L, OEMS
322B L, 322C, 324D FM, 325B L, OEMS
4367100
MOTOR GP-GEAR
CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
1132917
MOTOR AS
320, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 L
320, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 L