AVSPARE.COM
parts catalog

MOTOR GP-PISTON 3585009 - Caterpillar


3585009 MOTOR GP-PISTON Caterpillar parts 236D, 242D
Rating:
16
Alternative (cross code) number:
CA3585009
358-5009
3585009
Caterpillar 3585009 MOTOR GP-PISTON
Weight: 127 pounds 57 kg.

Buy MOTOR GP-PISTON 3585009 Caterpillar genuine, new aftermarket tractor parts with delivery
SKID STEER LOADER,

Compatible equipment models: 3585009:

SKID STEER LOADER  236D   242D   Caterpillar
Number on catalog scheme: 1
  For full view, you need register

Information:


Illustration 7 g00566369
Torque Limiter for the C2 Series Backhoe Loader (9) Adjustment screw. (10) Locknut.
Loosen locknut (10) and turn screw (9) clockwise in order to increase the flow. Turn adjustment screw (9) counterclockwise in order to decrease the flow. Note: A half turn of adjustment screw (9) will change the flow approximately 3.8 L/min (1 US gpm). Never, adjust screw (9) more than three and a half turns. Adjusting the screw (9) more may damage the internal spring. If the spring fails, the pump performance will be poor.
After the adjustment is made, tighten the locknut. Repeat Steps 13, 14, 15, 2, 17, and 16.
If the flow is not within the specification, then adjust the torque limiter. Stop the engine. Repeat steps 19 and 20. If the torque limiter is not within the specification after several attempts, then rework the torque limiters. Go to the next test in order to Rework the Torque Limiter. Repeat the test and adjust for the torque limiter after you rework the torque limiter.
When the flow is within the specification, remove the test equipment.
Remove hose (6) from the 6V-8946 Reducer Assembly. Remove 6V-9831 Cap Assembly from tube (5). Place a new O-ring onto the fitting and reinstall hose (6) to tube (5) .
Remove hose (4) from the 6V-8946 Reducer Assembly. Remove 6V-9832 Cap Assembly from elbow (3). Place a new O-ring onto the fitting and reinstall hose (4) to elbow (3) .
Replace hoses (4) and (6) into the two retainers (8) on the boom for the two hoses. Reinstall the four bolts (7). There are two bolts on each retainer (8). Reinstall the retainers (8) on the boom for the hoses.
Replace the floorplate. Reinstall the four screws that hold the floorplate in place.
Replace the floormat. Reinstall the four screws that hold the two plates for the floormat. There are two screws on each plate. The plates are located at the edge of each door in the cab.Rework the torque limiter
Note: If the torque limiter cannot be set within the specification, then replace the torque limiter.Note: This procedure will not increase the lifting capacity of the machine.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure the bucket and/or all of the attachments have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to

Caterpillar parts catalog:

Caterpillar parts catalog
236D Skid Steer Loader BGZ00001-UP (MACHINE) POWERED BY C3.3B Engine
242D Skid Steer Loader DZT00001-UP (MACHINE) POWERED BY C3.3B Engine
236D Skid Steer Loader MPW00001-UP (MACHINE)
242D Skid Steer Loader A9W00001-UP (MACHINE)
226D Skid Steer Loader HR600001-UP (MACHINE) POWERED BY C2.2 Engine
232D Skid Steer Loader DPR00001-UP (MACHINE) POWERED BY C2.2 Engine
236D3 Skid Steer Loader AZ600001-UP (MACHINE) POWERED BY C3.3B Engine
242D3 Skid Steer Loader HSX00001-UP (MACHINE) POWERED BY C3.3B Engine
226D3 Skid Steer Loader D5R00001-UP (MACHINE) POWERED BY C2.2 Engine
232D3 Skid Steer Loader D5Z00001-UP (MACHINE) POWERED BY C2.2 Engine
236D Skid Steer Loader BGZ00001-UP (MACHINE) POWERED BY C3.3B Engine
242D Skid Steer Loader DZT00001-UP (MACHINE) POWERED BY C3.3B Engine
226D Skid Steer Loader HR600001-UP (MACHINE) POWERED BY C2.2 Engine
232D Skid Steer Loader DPR00001-UP (MACHINE) POWERED BY C2.2 Engine


Parts motor Caterpillar catalog:

2582579 MOTOR & MTG GP-HYDRAULIC FAN
216B3, 226B3, 236B3, 236D, 242B3, 242D, 246C, 246D, 247B3, 252B3, 256C, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C...
3073036 MOTOR GP-GEAR
216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 236D, 242B, 242B3, 242D, 247B, 247B3, 252B, 252B3, 257B, 257B3, 257D, 259B3, 259D
3791084 MOTOR GP-WINDOW WIPER
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
2957221 MOTOR & MTG GP-HYDRAULIC FAN
216B3, 226B3, 236B, 236B3, 236D, 242B3, 242D, 247B3, 252B, 252B3, 257B3, 257D, 259B3, 259D
2582577 MOTOR GP-GEAR
216B3, 226B3, 236B3, 236D, 242B3, 242D, 246C, 246D, 247B3, 252B3, 256C, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.