3826587 MOTOR-STARTING Caterpillar parts
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, C4.4, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B
Rating:
Alternative (cross code) number:
CA3826587
382-6587
3826587
CA3826587
382-6587
3826587
Weight: 22 pounds 9 kg.
EXCAVATOR, VIBRATORY COMPACTOR,
You can buy:
US$642.89
15 Jul 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Total Power Parts MAH-MS147 Starter Compatible with/Replacement for Caterpillar CB66B 11.131.899, 11.132.187, AZF4699, IS1294, MS147, 11.132.187, AZF4839, is 1294, 321-8968, 382-6587
Total Power Parts Specs: Starter, Compatible with/Replacement for: Letrika/ AZF48, Volt: 24, Power: 5.500 kw, Hp: 7.376, Condition: New, Rotation Direction: Clockwise, Electric Starter Type: Permanent Magnet Gear Reduction (PMGR), Number Of Teeth: 10, Gear OD: 1.559", Gear OD: 39.600mm, Mount Hole ID 1: 12mm, Mount Hole 1 Type: Unthreaded, Mount Hole 2 Type: Unthreaded, Mount Hole ID 3: 12mm, Mount Hole 3 Type: Unthreaded || Compatible with/Replacement for OEM Numbers: Arrowhead: IS1294, MS147, Caterpillar: 321-8968, 382-6587, Letrika/Iskra: 11.132.187, AZF4839, IS 1294, : 11.131.899, 11.132.187, AZF4699, IS1294, MS147 || Compatible With/Replacement For: Caterpillar CB66B || 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. But in a rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you, contact us for a replacement. || 100% New aftermarket Starter built to meet OEM specifications
Total Power Parts Specs: Starter, Compatible with/Replacement for: Letrika/ AZF48, Volt: 24, Power: 5.500 kw, Hp: 7.376, Condition: New, Rotation Direction: Clockwise, Electric Starter Type: Permanent Magnet Gear Reduction (PMGR), Number Of Teeth: 10, Gear OD: 1.559", Gear OD: 39.600mm, Mount Hole ID 1: 12mm, Mount Hole 1 Type: Unthreaded, Mount Hole 2 Type: Unthreaded, Mount Hole ID 3: 12mm, Mount Hole 3 Type: Unthreaded || Compatible with/Replacement for OEM Numbers: Arrowhead: IS1294, MS147, Caterpillar: 321-8968, 382-6587, Letrika/Iskra: 11.132.187, AZF4839, IS 1294, : 11.131.899, 11.132.187, AZF4699, IS1294, MS147 || Compatible With/Replacement For: Caterpillar CB66B || 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. But in a rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you, contact us for a replacement. || 100% New aftermarket Starter built to meet OEM specifications
YANNAL PART C4.4 Starter Motor 3826587 Suitable for Caterpillar Engine
YANNAL PART High-quality starter motor designed for Caterpillar C4.4 engines || Constructed with premium materials for durability and long-lasting performance || Direct replacement for part number 3826587, ensuring a perfect fit and easy installation || Provides reliable starting power to the engine for smooth operation || Engineered to meet or exceed OEM specifications for optimal performance
YANNAL PART High-quality starter motor designed for Caterpillar C4.4 engines || Constructed with premium materials for durability and long-lasting performance || Direct replacement for part number 3826587, ensuring a perfect fit and easy installation || Provides reliable starting power to the engine for smooth operation || Engineered to meet or exceed OEM specifications for optimal performance
Nayuank Starter Motor 24V 10T 3826587 3218968 T411409 Fits For Caterpillar CAT Engine C4.4 Excavator 312E 312EL 314ECR 314ELCR 316EL 318EL
Nayuank Part Name: Starter Motor || Part Number: 3826587 3218968 T411409 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: C4.4 || Applicable: Fits For Caterpillar CAT Engine C4.4 Excavator 312E 312EL 314ECR 314ELCR 316EL 318EL || Package included: 1pcs Starter Motor 24V 10T 3826587 3218968 T411409
Nayuank Part Name: Starter Motor || Part Number: 3826587 3218968 T411409 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: C4.4 || Applicable: Fits For Caterpillar CAT Engine C4.4 Excavator 312E 312EL 314ECR 314ELCR 316EL 318EL || Package included: 1pcs Starter Motor 24V 10T 3826587 3218968 T411409
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 3826587:
Information:
Note: Ensure that the desired diagnostic code (CID FMI) is on hold. Ensure that the "SERV CODE" indicator is ON. Find the connector contact that is located on the Main Display Module. Use the electrical system schematic for the engine that is being serviced to find the connector contact that corresponds to the CID that is shown.This diagnostic code is recorded when the Main Display Module reads a signal from the sender that is too low. The Gauge Needle will be in the warning region as a result of this diagnostic condition. The following examples are possible causes.
The engine oil temperature sender has a problem.
The sender signal circuit that is located in the engine is shorted to ground.
The Main Display Module has a problem.Note: The Main Display Module is unable to determine when a sender or the signal harness circuit of a sender is open or the resistance is too high. As a result of this condition, a Gauge Needle will always be on the far left of the scale. This condition is recognized as a gauge with a needle that is always at the far left of the scale.
Measure the Resistance of the Sender.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the sender.
Measure the resistance that is between the threads of the terminal and the case of the sender. The following table illustrates the correct approximate resistance for the following temperatures.
Table 1
Approximate Resistances For The Sender Connector Contacts
Temperature Resistance
54.4 °C (130.0 °F) 850 to 1050 Ohms
110 °C (230 °F) 140 to 160 Ohms
Check the Display Area and the Harness.
Turn the "ECS" switch to the OFF/RESET position.
Check for loose connections or corroded connections to the sender.
Replace the corroded contacts and tighten the loose connections.
Turn the "ECS" switch to the COOLDOWN/STOP position. The "SERV CODE" indicator should be ON for the diagnostic code CID 0175 FMI 04.
Disconnect the engine harness from the sender.
Observe the "SERV CODE" indicator.Expected Result: The "SERV CODE" indicator should turn OFF.Results:
OK - The "SERV CODE" indicator turns OFF. The sender has a problem. Replace the sender.
Not OK - The "SERV CODE" indicator stays ON. The harness wiring or the Main Display Module has a problem. Proceed to Step 3.
Check the Sender Wire for a Short to Ground.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the sender.
Turn the "ECS" switch to the COOLDOWN/STOP position.
Measure the voltage from ground to the sender.Expected Result: The voltage should be 6.0 0.5 DCV.Results:
OK - The voltage is 6.0 0.5. If the SERV CODE indicator is still ON, repeat Step 1 through STEP 3. If the cause of the diagnostic fault is not found, replace the Main Display Module.
Not OK - The voltage is less than 0.5 DCV. The harness wiring has a problem. There is an open circuit or a short to ground in the signal wire for the sender, or a poor terminal connection or a poorly
The engine oil temperature sender has a problem.
The sender signal circuit that is located in the engine is shorted to ground.
The Main Display Module has a problem.Note: The Main Display Module is unable to determine when a sender or the signal harness circuit of a sender is open or the resistance is too high. As a result of this condition, a Gauge Needle will always be on the far left of the scale. This condition is recognized as a gauge with a needle that is always at the far left of the scale.
Measure the Resistance of the Sender.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the sender.
Measure the resistance that is between the threads of the terminal and the case of the sender. The following table illustrates the correct approximate resistance for the following temperatures.
Table 1
Approximate Resistances For The Sender Connector Contacts
Temperature Resistance
54.4 °C (130.0 °F) 850 to 1050 Ohms
110 °C (230 °F) 140 to 160 Ohms
Check the Display Area and the Harness.
Turn the "ECS" switch to the OFF/RESET position.
Check for loose connections or corroded connections to the sender.
Replace the corroded contacts and tighten the loose connections.
Turn the "ECS" switch to the COOLDOWN/STOP position. The "SERV CODE" indicator should be ON for the diagnostic code CID 0175 FMI 04.
Disconnect the engine harness from the sender.
Observe the "SERV CODE" indicator.Expected Result: The "SERV CODE" indicator should turn OFF.Results:
OK - The "SERV CODE" indicator turns OFF. The sender has a problem. Replace the sender.
Not OK - The "SERV CODE" indicator stays ON. The harness wiring or the Main Display Module has a problem. Proceed to Step 3.
Check the Sender Wire for a Short to Ground.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the sender.
Turn the "ECS" switch to the COOLDOWN/STOP position.
Measure the voltage from ground to the sender.Expected Result: The voltage should be 6.0 0.5 DCV.Results:
OK - The voltage is 6.0 0.5. If the SERV CODE indicator is still ON, repeat Step 1 through STEP 3. If the cause of the diagnostic fault is not found, replace the Main Display Module.
Not OK - The voltage is less than 0.5 DCV. The harness wiring has a problem. There is an open circuit or a short to ground in the signal wire for the sender, or a poor terminal connection or a poorly
Caterpillar parts catalog:
Parts motor Caterpillar catalog:
318C, 318E L, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, ...
2742636
MOTOR GP-SWING
314D CR, 314D LCR, 314E CR, 314E LCR
314D CR, 314D LCR, 314E CR, 314E LCR
308C, 308D, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H...
C4.4
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314E CR, 314E LCR, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L,...
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 34...
3639459
MOTOR AS
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 34...
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 34...
4229182
MOTOR GP-SWING
312E, 312E L
312E, 312E L
4202395
MOTOR AS
314E CR, 314E LCR
314E CR, 314E LCR
4202400
MOTOR AS
314E CR, 314E LCR
314E CR, 314E LCR
583T, 587R, 587T, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 770, 770G, 770G OEM, 772, 772G, 772G OEM, 914G, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 930G...
C6.6, C7.1
2932012
MOTOR-FAN
SPF343C
SPF343C
2886581
MOTOR STARTER
C0.5, C0.7
C0.5, C0.7
D353C
3F5462
MOTOR
D342, D353C
D342, D353C
3L1234
MOTOR ASSEM.
D353C
D353C
9F9776
MOTOR ASSEM.
D342
D342
3054C, C4.4
C4.4