AVSPARE.COM
parts catalog

MOTOR & MTG GP-VENTILATION 3967161 - Caterpillar



3967161 MOTOR & MTG GP-VENTILATION Caterpillar parts MOTOR
Rating:
86
Alternative (cross code) number:
CA3967161
396-7161
3967161
Caterpillar 3967161 MOTOR & MTG GP-VENTILATION

Buy MOTOR & MTG GP-VENTILATION 3967161 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 20
  
  For full view, you need register

Information:

Bucket Zero Adjustment
The "Bucket Zero" calibration should be performed daily, when one of the following conditions apply:
The "Bucket Zero Interval" has expired.
The work tool has changed.
A calibration alert is displayed on the monitor.
A calibration of the "Boom Single Operation" and "Front Multi Operation" has been performed.To perform the "Bucket Zero Adjustment" calibration:
Navigate to the "Work Tool Select" menu. Refer to the Cat®"Production Measurement Menu Screen".
Select the work tool.
Press the "Calibrate" function key.
Use the keypad to select "Bucket Zero Adjustment" . Press the "OK" function key to start the calibration.Note: The "Bucket Zero" function key can also be selected from any screen to open the "Bucket Zero Adjustment" menu.
Illustration 11 g03867811
Follow the instruction on the monitor screen to:
Calibrate the weight of an empty bucket. Gradually raise and swing the bucket at least 90 degrees to simulate truck loading. Each calibration requires five cycles to complete the "Bucket Zero Adjustment" calibration.The following table details the possible failure messages that can be logged. The list is accompanied by suggested operations for correcting the failures.
Table 3
Log Failed Message Reason / Required Operation
Boom is too high. Retry this cycle from the initial position.
- Start Boom Operation from lower position.
- Raise Boom more slowly.
Swing operation time is too short. Retry this cycle from the initial position.
- Maintain swing speed over a slower and longer cycle.
Bucket is not level. Retry this cycle from the initial position.
- Maintain the bucket angle similar to loading operation (Carry position).
Boom operation is too slow. Calibration cycle has timed out.
Retry this cycle from the initial position
- Raise Boom more quickly.
- Start Boom operation from a lower position. Simple Calibration
Simple calibration will adjust the system calibration to match a reference scale. Simple calibration can be performed on as few as 1 or as many as 15 trucks. The more trucks used, the better the calibration is fine-tuned. The recommended minimum number of trucks for most applications is 5.When performing a Simple Calibration, record the following:
The weight of the trucks at the scale house.
The weight that is displayed by the scale system for the trucks.
A recent tare weight of the trucks being used for the simple calibration.
Illustration 12 g06018439
Weighing calibration function screen.
From the "Main Menu", go to "Work Tool Select" submenu. From the "Work Tool Select" submenu, go to "Weighing Calibration" screen and select "Simple Calibration". Press the "OK" key.
Illustration 13 g06018451
Select and input the scale weight for the appropriate truck number. Continue to input the scale weight if you have multiple data.
Press the "OK" key when finished entering all scale weight information.
The "Bucket Payload" is adjusted from the next bucket load.Note: The simple calibration update cannot be performed unless the operator presses the store button after each truck load. The simple calibration truck list remains when the machine is keyed to the OFF position.When performing a simple calibration keep the following information in mind:
A new simple calibration erases all prior simple calibrations.
Only the latest simple calibration on one or more trucks is used to fine-tune the scale system.
Once a simple calibration is started, additional

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
AP1055 F Asphalt Paver TJ500001-UP (MACHINE) POWERED BY C7.1 Engine
AP1000 F Asphalt Paver AC400001-UP (MACHINE) POWERED BY C7.1 Engine
AP1055 F Asphalt Paver RLM00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts motor Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.