MOTOR GP-STG-B 5425974 - Caterpillar

5425974 MOTOR GP-STG-B Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA5425974
542-5974
5425974

Weight: 63 pounds 28 kg.

Buy MOTOR GP-STG-B 5425974 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:

5425974 MOTOR GP-STG -B 20R6874 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

#US Replacement part for Carburetor Rebuild Kit for 2000-2002 for Suzuki LT-F300F KingQuad 4x4 for ATV carbPart#5425974

$141.99

03 Oct 2025

RU: GOTENK

#US Replacement part for Carburetor Rebuild Kit for 2000-2002 for Suzuki LT-F300F KingQuad 4x4 for ATV carbPart#5425974
Generic NOTE - Package included: 1 Set ONLY. Please check all carefully (photos and model) and make sure it will compatible with your original one. || Manufacturer Part Number: 1217-A125012- for ATV

Number on catalog scheme: 3

Caterpillar 5425974 Parts scheme MOTOR GP-STG-B

For full view, you need register

Information:

Align the split in the spring pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole in the carrier. Each stake mark should be approximately 1.5 mm (0.059 inch) from the outside diameter of the spring pin hole.
Repeat steps 41.a through 41.f in order to install the other two planetary gears in the carrier.
Install carrier assembly (19) into gear. The weight of carrier assembly (19) is approximately 14 kg (30 lb).
Illustration 87 g00781466
Install retaining ring (18). Retaining ring (18) will secure carrier assembly (19) in position.
Illustration 88 g00781412
Install spacer (17). Install gear (16) .
Assemble carrier assembly (15), as follows.
Illustration 89 g00781407
Install carrier assembly in position on gear (16) .
Illustration 90 g00781401
Install retaining ring (14) onto gear (16) .
Illustration 91 g00780432
Install washer (11). Install bearing assembly (13). Install gear (12). Install washer (11). Install retaining ring (10) with Tooling (D) .
Repeat Steps 45.a through 45.c for the other two planetary gears.
Illustration 92 g00780428
Install spacer (9). Install gear (8) .
Apply 1U-8846 Gasket Sealant to the mating surfaces of cover (2) and housing (36) .
Illustration 93 g00879365
Install O-ring seal (7) on plug (4) .
Illustration 94 g00879362
Install plug (4) in cover (2). Replace plate (6) if wear is shown. Position gear (5). Install bolts (3) .
Illustration 95 g00708090
Install cover (2) with Tooling (B). The weight of the cover is approximately 32 kg (70 lb).
Remove cover (2) .
Illustration 96 g00783116
Adjust clearance between plate (5) and gear (8) between 1.000 + 1.000 mm (0.0394 + 0.0394 inch).
Attach Tooling (B) to cover (2). Install cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb).
Illustration 97 g00708089
Install bolts (1) and the washers. Tighten bolts (1) in a crisscross pattern to a torque of 420 60 N m (310 44 lb ft). Tighten new bolts (1) and additional 60 degrees.
Illustration 98 g00783362
Remove plug (6). Attach Tooling (J) to cover (2). Reduce the air pressure at the source to 103 kPa (15 psi). Apply air pressure to Tooling (J). This air will test the Duo-Cone seal kits.
Use the ball valve on Tooling (J) to eliminate the air pressure to the final drive. A pressure of 98 kPa (14.2 psi) must be maintained for 30 seconds.
Remove Tooling (J). Install plug (6). Torque plug (6) to 80 10 N m (59 7 lb ft).
Remove the final drive from Tooling (A). The combined weight of the final drive and final drive sprocket is approximately 310 kg (683 lb).End By: Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".