9P2218 MOTOR AS Caterpillar parts
245, 637D, 815B, 826C, 943, 950B, 953, 955L, 963, 966D, 980C, D6D, D7G
Rating:
Alternative (cross code) number:
CA9P2218
9P-2218
9P2218
CA9P2218
9P-2218
9P2218
Weight: 7 pounds 3 kg.
EXCAVATOR, WHEEL TRACTOR,
Compatible equipment models: 9P2218:
Number on catalog scheme:
13
For full view, you need register
Information:
following procedures are used in order to functionally check a Type III governor. The housing cover plug and the seal for the throttle stop do not need to be removed. This check is intended as an aid to determine if a governor is functioning correctly.
Install the governor on the governor calibration bench. Refer to the Testing and Adjusting, "Installation Of Governor On 1U-7326 Governor Calibration Bench " section in this manual for installation procedures.Note: The load stop is set higher than 9.00 mm (0.354 inch) and the calibration must be set. Refer to the Testing and Adjusting, "Setting the Governor Load Stop Dimension For More Than 9.00 mm" section in this manual.Note: Follow all of the operating procedures for the governor calibration bench that are specified in the procedure for checking other types of governors.All specifications for the governor adjustment procedure are in the Technical Marketing Information (TMI). When you check a previously adjusted governor, the tolerance ( ) factor must be doubled. This will be referred to as an expanded tolerance.
Adjust the speed of the calibration bench to the LOAD STOP rpm that is specified in the TMI. Slowly move the throttle to the LOW IDLE position and back to the THROTTLE STOP position. Do not move the throttle again during this checking procedure.
Check the governor output dimension. The governor output dimension should be within the expanded tolerance dimension in "FUNC CHECK #2" of the TMI.
Adjust the speed of the calibration bench to the "THROT STOP ADJ" rpm from the TMI. Wait for one minute in order for the output dimension to be within the "THROT STOP ADJ" expanded tolerance dimension. If the output dimension is still changing, you may need to wait longer.The governor is operating correctly and the governor can be used again without any adjustment if the performance of the governor is acceptable according to the tolerance checks. If the governor fails any of the above tests, follow the procedures toward the end of the checking procedure for the other types of governors in the Testing and Adjusting, "Governor (Types I, II, IV, and V) - Check".
Reduce the speed of the calibration bench to the lowest setting. Turn the switch to the OFF position. The tachometer will turn off automatically after a short period of time.
After the governor has been installed on the engine and the low idle speed has been adjusted, seal the throttle adjustment screw with the lockwire and the tamper resistant seal.
Install the governor on the governor calibration bench. Refer to the Testing and Adjusting, "Installation Of Governor On 1U-7326 Governor Calibration Bench " section in this manual for installation procedures.Note: The load stop is set higher than 9.00 mm (0.354 inch) and the calibration must be set. Refer to the Testing and Adjusting, "Setting the Governor Load Stop Dimension For More Than 9.00 mm" section in this manual.Note: Follow all of the operating procedures for the governor calibration bench that are specified in the procedure for checking other types of governors.All specifications for the governor adjustment procedure are in the Technical Marketing Information (TMI). When you check a previously adjusted governor, the tolerance ( ) factor must be doubled. This will be referred to as an expanded tolerance.
Adjust the speed of the calibration bench to the LOAD STOP rpm that is specified in the TMI. Slowly move the throttle to the LOW IDLE position and back to the THROTTLE STOP position. Do not move the throttle again during this checking procedure.
Check the governor output dimension. The governor output dimension should be within the expanded tolerance dimension in "FUNC CHECK #2" of the TMI.
Adjust the speed of the calibration bench to the "THROT STOP ADJ" rpm from the TMI. Wait for one minute in order for the output dimension to be within the "THROT STOP ADJ" expanded tolerance dimension. If the output dimension is still changing, you may need to wait longer.The governor is operating correctly and the governor can be used again without any adjustment if the performance of the governor is acceptable according to the tolerance checks. If the governor fails any of the above tests, follow the procedures toward the end of the checking procedure for the other types of governors in the Testing and Adjusting, "Governor (Types I, II, IV, and V) - Check".
Reduce the speed of the calibration bench to the lowest setting. Turn the switch to the OFF position. The tachometer will turn off automatically after a short period of time.
After the governor has been installed on the engine and the low idle speed has been adjusted, seal the throttle adjustment screw with the lockwire and the tamper resistant seal.
Cat SIS web machinery list:
Parts motor Caterpillar catalog:
824C, 824G II, 824H, 825G II, 825H, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972M XE, 980C, 980G II
245, 3406, 3412, 621B
920, 930, 950, 950B, 963
215, 943, 953
920, 936, 936F, 950B, 963, D5H, G936
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 229, 518C, 528B, 530B, 621F,...
135H, 135H NA, 143H, 14H, 14H NA, 160H ES, 160H NA, 163H NA, 517, 527, 539, 572R, 816F, 816F II, 824H, 826C, 826G, 826G II, 826H, 834G, 834H, 836, 836G, 836H, 950H, 953C, 963C, 966H, 973C, 988G, 988H,...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 517, 527, 611, 613C, 613C II, 615C, 621E, 621F, 621G, 623E, 6...
16G, 517, 518, 527, 613B, 637D, 815B, 834B, 943, 953, 980C, 988B, 992C, D4E, D4H, D4H XL, D4HTSK III, D5HTSK II
815B, 826C, 980C, 980F
7G0248
MOTOR ASSEM.
D10, D7G, D9H
D10, D7G, D9H
9D0202
MOTOR ASSEM.
120G, 130G, 14E, 14G, 16G, 227, 235, 245, 621B, 621R, 641B, 920, 941, 950, 950B, 955L, 966D, 977K, 988, 988B, D10, D4D, D4E, D6D
120G, 130G, 14E, 14G, 16G, 227, 235, 245, 621B, 621R, 641B, 920, 941, 950, 950B, 955L, 966D, 977K, 988, 988B, D10, D4D, D4E, D6D
9P2217
MOTOR ASSEM.
227, 245, 621, 623B, 633D, 637D, D6D, D7G
227, 245, 621, 623B, 633D, 637D, D6D, D7G
3P8379
MOTOR ASSEM.
920, 941, 955L, D6C, D8K, D9H
920, 941, 955L, D6C, D8K, D9H
5C7459
MOTOR
215
215
9G8181
MOTOR ASSEM.
120G, 130G, 225, 235, 816, 950
120G, 130G, 225, 235, 816, 950
6N9765
MOTOR ASSEM.
215, 215B, 225, 227, 245
215, 215B, 225, 227, 245
120G, 12G, 130G, 140G, 16G, 235B, 834B
9W0213
MOTOR AS
225, 225D
225, 225D
120G, 12G, 130G, 140G, 227, 245, 508, 518, 518C, 528B, 530B
6T6216
MOTOR AS-WIPER
120G, 120H, 12G, 12H NA, 130G, 140G, 140H NA, 16G, 245, 518, 621E, 815B, 824C, 826C, 916, 924F, 926, 936, 936F, 950B, 950F, 950F II, 953, 960F, 966F, 966F II, 970F, 973, 980C, 980F, CP-563, CS-573, CS...
120G, 120H, 12G, 12H NA, 130G, 140G, 140H NA, 16G, 245, 518, 621E, 815B, 824C, 826C, 916, 924F, 926, 936, 936F, 950B, 950F, 950F II, 953, 960F, 966F, 966F II, 970F, 973, 980C, 980F, CP-563, CS-573, CS...
206, 214, CB-424
120G, 130G, 215, 215B, 227, 245, 621, 641B, 834B, 941, 988B, 992C