1851598 MOUNTING GP-BANK VALVE Caterpillar parts
416D, 420D, 424D, 428D, 430D, 438D
Rating:
Alternative (cross code) number:
CA1851598
185-1598
1851598
CA1851598
185-1598
1851598
BACKHOE LOADER,
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 439-3940 Link Bracket 2
6V-3668 12 MM Bolt 2
5P-8245 Washer 2
B 339-9353 High Press. Cap Kit 1
265-2256 Wipers 1
(1) Use one to remove the fuel pump from the EPG engine.Start By:
Remove the fuel transfer pump.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury.
Note: Use Tooling (B) to cap tube assemblies, fittings, ports, and any openings on the fuel system to prevent contamination.
Illustration 1 g03688101
Remove tube assembly (1), tube assembly (2), tube assembly (3), and tube assembly (4).
Illustration 2 g03689368
Disconnect tube assembly (5).
Remove tube assembly (6), tube assembly (8), and tube assembly (9).
Remove bolts (7) and remove fuel manifold (10).
Illustration 3 g03691068
Disconnect harness assembly (11), harness assembly (13), harness assembly (14), and harness assembly (15).
Remove tube assembly (12) and tube assembly (16). Do not reuse bolts for tube assembly (16).
Illustration 4 g03691284
Attach Tooling (A) and a suitable lifting device to high-pressure fuel pump (18). The weight of high-pressure fuel pump is approximately 125 kg (276 lb).
Remove bolts (17), bolts (19), and high-pressure fuel pump (18).Note: The lifting device should not come into contact with the fuel shutoff valve to prevent damage to the component.! Magnetic lift is prohibited for the C175 HP fuel pump.Installation Procedure
Note: When Tooling (B) is removed, be careful to prevent contamination.
Install the high-pressure fuel pump (18) in the reverse order of removal.
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 439-3940 Link Bracket 2
6V-3668 12 MM Bolt 2
5P-8245 Washer 2
B 339-9353 High Press. Cap Kit 1
265-2256 Wipers 1
(1) Use one to remove the fuel pump from the EPG engine.Start By:
Remove the fuel transfer pump.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury.
Note: Use Tooling (B) to cap tube assemblies, fittings, ports, and any openings on the fuel system to prevent contamination.
Illustration 1 g03688101
Remove tube assembly (1), tube assembly (2), tube assembly (3), and tube assembly (4).
Illustration 2 g03689368
Disconnect tube assembly (5).
Remove tube assembly (6), tube assembly (8), and tube assembly (9).
Remove bolts (7) and remove fuel manifold (10).
Illustration 3 g03691068
Disconnect harness assembly (11), harness assembly (13), harness assembly (14), and harness assembly (15).
Remove tube assembly (12) and tube assembly (16). Do not reuse bolts for tube assembly (16).
Illustration 4 g03691284
Attach Tooling (A) and a suitable lifting device to high-pressure fuel pump (18). The weight of high-pressure fuel pump is approximately 125 kg (276 lb).
Remove bolts (17), bolts (19), and high-pressure fuel pump (18).Note: The lifting device should not come into contact with the fuel shutoff valve to prevent damage to the component.! Magnetic lift is prohibited for the C175 HP fuel pump.Installation Procedure
Note: When Tooling (B) is removed, be careful to prevent contamination.
Install the high-pressure fuel pump (18) in the reverse order of removal.
Caterpillar SIS machinery equipment:
Caterpillar SIS
416D Backhoe Loader BFP00001-17198 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader FDP00001-07198 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
430D Backhoe Loader BNK00001-02501 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
424D Backhoe Loader BGP00001-00647 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader BLL00001-00650 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader BMT00001-01617 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
438D Backhoe Loader BPE00001-00663 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BGJ00001-00522 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader BKC00001-00501 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BKG00001-01299 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BFP05178-17198 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader FDP07199-18399 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
430D Backhoe Loader BNK02502-05899 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader BMT01618-03227 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
438D Backhoe Loader BPE00664-00742 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BGJ00523-01315 (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader BKC00502-UP (MACHINE) POWERED BY 3054 Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BKG01300-UP (MACHINE) POWERED BY 3054B Engine »
185-1598
MOUNTING GP-BANK VALVE
424D Backhoe Loader CJZ00001-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader BXC00001-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
428D Backhoe Loader MBM00001-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader BFP12900-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader FDP18400-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
420D Backhoe Loader BLN10300-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
430D Backhoe Loader BNK05900-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
416D Backhoe Loader B2D00001-UP (MACHINE) POWERED BY 3054C Engine »
185-1598
MOUNTING GP-BANK VALVE
Cat SIS web machinery list:
Parts mounting Caterpillar catalog:
3593939
MOUNTING GP-SNOW WING
120M, 120M 2, 12M
120M, 120M 2, 12M
1238775
MOUNTING GP-ENGINE
3606, 3608, 3612, 3616, C280-12, C280-16, C280-6, C280-8, G3606, G3606B, G3608, G3612, G3616
3606, 3608, 3612, 3616, C280-12, C280-16, C280-6, C280-8, G3606, G3606B, G3608, G3612, G3616
2460600
MOUNTING GP-ALTERNATOR
973C, D6R, D6R III, D6R STD, D6T, D7R XR
973C, D6R, D6R III, D6R STD, D6T, D7R XR
8Y5316
MOUNTING GP-CAB
931C II, 935C II
931C II, 935C II
3871566
MOUNTING GP
450E
450E
1801679
MOUNTING GP-SNOW WING
12H, 140H, 140K, 140K 2, 143H, 160H, 160K, 163H
12H, 140H, 140K, 140K 2, 143H, 160H, 160K, 163H
1366068
MOUNTING GP-TANK
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1951123
MOUNTING GP-TRANSMISSION
735, 735B, 740, 740B
735, 735B, 740, 740B
2692823
MOUNTING GP-AIR CLEANER
3512C, TH48-E80
3512C, TH48-E80