2V0960 MOUNTING MODIFICATIONS GROUP Caterpillar parts
235
Rating:
Alternative (cross code) number:
CA2V0960
2V-0960
2V0960
CA2V0960
2V-0960
2V0960
Weight: 111 pounds 50 kg.
EXCAVATOR,
Compatible equipment models: 2V0960:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01383106
Remove cover (1).
Illustration 2 g01383107
Remove cover (2).
Illustration 3 g01377908
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 4 g01383131
Disconnect harness assemblies (3). Disconnect hose assemblies (4).
Illustration 5 g00694257
Illustration 6 g00694258
Remove cable straps (5). Disconnect hose assembly (7).
Remove bolts (6). Remove control manifold (8).
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01383106
Remove cover (1).
Illustration 2 g01383107
Remove cover (2).
Illustration 3 g01377908
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 4 g01383131
Disconnect harness assemblies (3). Disconnect hose assemblies (4).
Illustration 5 g00694257
Illustration 6 g00694258
Remove cable straps (5). Disconnect hose assembly (7).
Remove bolts (6). Remove control manifold (8).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts mounting Caterpillar catalog:
1W1852
MOUNTING GP-ALTERNATOR
3408, 3412, 3412C, G3408, G3408C, G3412
3408, 3412, 3412C, G3408, G3408C, G3412
8N1638
MOUNTING GP-ALTERNATOR
3408, 3412
3408, 3412
6N0524
MOUNTING & CONDENSER GP
992C, 992D
992C, 992D
2V3895
MOUNTING GP-PLATFORM
992C, 992D
992C, 992D