MTG GP-PRELUBE 4676267 - Caterpillar

Install Tooling (E) and Tooling (C) on Tooling (D).
Install Tooling (G), Tooling (J), and Tooling (K) on Tooling (A). Use Tooling (F) to apply pressure on Tooling (E).
Illustration 5 g01309721
The recoil spring retainer must never be more than 12.7 mm (0.50 inch) from the recoil spring while the spring is being removed. Be sure the pressure reading on the pressure gauge of the tool gradually decreases during all the steps of the procedure.
Extend Tooling (E) to 12.7 mm (0.50 inch) less than maximum travel. Use Tooling (K) to adjust Tooling (H) to the back of the cylinder. Keep Tooling (H) parallel to roller frame (1).
Pressurize Tooling (E). Remove the spring tension on retainer (3). Back off retainer (3) to a dimension of 12.7 mm (0.50 inch) with the use of Tooling (L).
Illustration 6 g00871426
Release the pressure on Tooling (E). The spring will rest on the retainer. Tooling (H) should be parallel to roller frame (1). Apply pressure to Tooling (E). Remove the spring tension on retainer (3). Back off retainer (3) 12.7 mm (0.50 inch) with the use of Tooling (L).
Illustration 7 g00871427
Release the pressure on Tooling (E). The spring will rest on retainer (3). Tooling (H) should be parallel with roller frame (1). Apply pressure to Tooling (E). Remove the spring tension on retainer (3). Back off retainer (3) 12.7 mm (0.50 inch) with the use of Tooling (L).
Illustration 8 g00871428
Release the pressure on Tooling (E). Back off Tooling (K). Tooling (H) should slide away from roller frame (1).
Illustration 9 g00871429
Extend Tooling (E) to 12.7 mm (0.50 inch) less than maximum travel. Use Tooling (K) to adjust Tooling (H) to the back of Tooling (E). Keep Tooling (H) parallel to roller frame (1). Pressurize Tooling (E). Remove the spring tension of retainer (3). Use Tooling (L) to back off retainer (3) to a dimension of 12.7 mm (0.50 inch).
Illustration 10 g00871430
Release the pressure on Tooling (E). Allow the spring to seat against the retainer. Adjust Tooling (H) to the back of the cylinder. Keep Tooling (H) parallel to roller frame (1). Pressurize Tooling (E). Remove the spring tension on retainer (3). Back off retainer (3) to a dimension of 12.7 mm (0.50 inch) with the use of Tooling (L).
Illustration 11 g00871431
Release the pressure on Tooling (E). The spring will rest on the retainer. Tooling (H) should be parallel with roller frame (1). Apply pressure to Tooling (E). Remove the spring tension on retainer (3). Back off retainer (3) 12.7 mm (0.50 inch) with the use of Tooling (L).
Illustration 12 g00871432
Release the tension of Tooling (E). The spring will rest on retainer (3). If any spring tension is remaining, repeat this procedure until there is no spring tension. If no spring tension is available remove all Tooling from roller frame (1). Note: If any spring tension is remaining, remove the nuts and washers. Remove spacers (G) and install the nuts and the washers against the plate. Repeat the previous steps.
Illustration 13 g00871433
Remove retainer (3) from roller frame (1).
Illustration 14 g00871434
Remove plate assembly (4) from roller frame (1).
Illustration 15 g00871435
Use