AVSPARE.COM
parts catalog

MTG GP-MONITOR 4Z6539 - Caterpillar



4Z6539 MTG GP-MONITOR Caterpillar parts MTG
Rating:
41
Alternative (cross code) number:
CA4Z6539
4Z-6539
4Z6539
Caterpillar 4Z6539 MTG GP-MONITOR
Weight: 0.09 pounds 0 kg.

Buy MTG GP-MONITOR 4Z6539 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 3
FMI 14 Troubleshooting    
Troubleshooting Test Steps    Values    Results    
1. Inspect The Harness Connections
A. Turn key start switch and disconnect switch OFF.
B. Inspect all harness connections related to the CAN data link. Make sure that the connectors are clean and tight.
C. Check the connectors for proper mating. Ensure that all the seals are present and in place.
D. Check the harness for signs of damage or abrasion.
E. Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
F. Check the exposed wires at the connectors for nicks or signs of abrasion.
G. Check for moisture inside the connector.    
The machine harness connectors are tight and free of corrosion.     OK - The machine harness connectors are tight and free of corrosion.
Proceed to Test Step 2.
NOT OK - The machine harness connectors are in need of repair.
Repair: Repair or replace the machine harness.
Proceed to Test Step 3.    
2. Verify The Hardware And The Software Part Numbers (1)
A. Verify that the following information is correct:
-The part number of the flash software for the ECM is correct.
-The part number of the ECM is correct.
-The part numbers of the sensors are correct.    
All of the part numbers are correct.     OK - All of the part numbers are correct.
Proceed to Test Step 3.
NOT OK - All of the part numbers are not correct.
Repair: The ECM or the sensors have the wrong part number or incorrect flash software is installed. Flash the correct software or replace the incorrect ECM or sensor with a module that has the correct part number. Refer to the Troubleshooting, "ECM - Flash Program" section for additional information.
Proceed to Test Step 3.    
3. Check If The Diagnostic Code Remains
A. Turn the key start switch and the disconnect switch ON.
B. Clear all diagnostic codes.
C. Operate the machine.
D. Stop the machine and engage the safety lock lever.
E. Check if the diagnostic code is active.    
The diagnostic code is no longer present.     OK - The diagnostic code does not exist at this time. The initial diagnostic code may have been caused by poor electrical connection or short at one of the harness connections. Resume machine operation.
STOP.
NOT OK - The diagnostic trouble code has not been corrected. If the diagnostic code has not been corrected after performing the procedure a second time, the ECM may require replacement.
Prior to replacing the ECM, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may affect repair time.
Follow the steps in Troubleshooting, "ECM - Replace" if the ECM needs to be replaced.
STOP.    
( 1 ) Consult your Caterpillar Authorized Dealer for the correct part numbers of the flash software.


Parts mtg Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.